Verilink NCC 2130 (880-503285-001) Product Manual - Manual (Page 22)

Configuration
3-4 Verilink NCC 2130 User Manual
Therefore, an “I” located in the slot 1 shelf 1 position represents an
NCC 2130, while an “I” located at some other position will
represent a TAC 2130.
Use the command “C”, which brings up the IDCSU Configuration
Menu.
Figure 3-2 IDCSU Configuration Menu
Configuration
Menu Commands
Commands and current settings for the network interface are
shown on the right side of the ASCII drawing on the IDCSU
Configuration Menu. Values and options for the synchronous
serial port (DTE interface) are shown on the left side.
Table 3-4 below describes the NCC 2130 IDCSU Configuration
Menu options:
IDCSU CONFIGURATION FW/HW Rev..1.25/0.8 IDCSU CONFIGURATION FW/HW Rev..1.25/0.8 IDCSU CONFIGURATION FW/HW Rev..1.25/0.8 IDCSU CONFIGURATION FW/HW Rev..1.25/0.8
|-----------------------|
|-----------------------| |-----------------------| |-----------------------|
-------<< dte <<-------| T) alm thld DEF |-------<< net <<-------
-------<< dte <<-------| T) alm thld DEF |-------<< net <<------- -------<< dte <<-------| T) alm thld DEF |-------<< net <<------- -------<< dte <<-------| T) alm thld DEF |-------<< net <<-------
M) mode 64K | | W) framing ESF
M) mode 64K | | W) framing ESF M) mode 64K | | W) framing ESF M) mode 64K | | W) framing ESF
N) scramble OFF | | F) format B8ZS
N) scramble OFF | | F) format B8ZS N) scramble OFF | | F) format B8ZS N) scramble OFF | | F) format B8ZS
C) clocking ST | | J) jitt buf 40 BITS
C) clocking ST | | J) jitt buf 40 BITS C) clocking ST | | J) jitt buf 40 BITS C) clocking ST | | J) jitt buf 40 BITS
G) los lead RTS | | L) lbo 0 DB
G) los lead RTS | | L) lbo 0 DB G) los lead RTS | | L) lbo 0 DB G) los lead RTS | | L) lbo 0 DB
------->> dte >>-------| I) idle code ONES |------->> net >>-------
------->> dte >>-------| I) idle code ONES |------->> net >>------- ------->> dte >>-------| I) idle code ONES |------->> net >>------- ------->> dte >>-------| I) idle code ONES |------->> net >>-------
|-----------------------| Z) density 12%+80z
|-----------------------| Z) density 12%+80z |-----------------------| Z) density 12%+80z |-----------------------| Z) density 12%+80z
lead toggles: DTR) DSR) RTS) CTS) DCD) lead toggles: DTR) DSR) RTS) CTS) DCD) lead toggles: DTR) DSR) RTS) CTS) DCD) lead toggles: DTR) DSR) RTS) CTS) DCD)
forced leads: Y N N N N
forced leads: Y N N N N forced leads: Y N N N N forced leads: Y N N N N
D) select DS-0 (1-24) B) timing NET D) select DS-0 (1-24) B) timing NET D) select DS-0 (1-24) B) timing NET D) select DS-0 (1-24) B) timing NET
01 02 03 04 05 06 07 08 09 10 11 12 P) prm NONE
01 02 03 04 05 06 07 08 09 10 11 12 P) prm NONE 01 02 03 04 05 06 07 08 09 10 11 12 P) prm NONE 01 02 03 04 05 06 07 08 09 10 11 12 P) prm NONE
13 14 15 16 17 18 19 20 21 22 23 24 C1-C7) canned config
13 14 15 16 17 18 19 20 21 22 23 24 C1-C7) canned config 13 14 15 16 17 18 19 20 21 22 23 24 C1-C7) canned config 13 14 15 16 17 18 19 20 21 22 23 24 C1-C7) canned config
O) poll far end (ON)
O) poll far end (ON) O) poll far end (ON) O) poll far end (ON)
A) Alarm ENABLE
A) Alarm ENABLE A) Alarm ENABLE A) Alarm ENABLE
V) Data Invert No
V) Data Invert No V) Data Invert No V) Data Invert No
[1,1] NEAR IDCSU 2130 > [1,1] NEAR IDCSU 2130 > [1,1] NEAR IDCSU 2130 > [1,1] NEAR IDCSU 2130 >