iSys iTerra TL1290 Color LED Printer - Manual (Page 5)

3
Safety Information
120-Volt Models
Your iSys product has been carefully designed to give you years of safe, reliable performance. As with all electrical equipment,
there are a few basic precautions you should take to avoid hurting yourself or damaging the product.
•
Carefully read the provided setup and operating instructions.
• Save all provided documentation for future reference.
• Read and follow all warning and instruction labels on the product itself.
• Unplug the product before you clean it. Use only a damp cloth; do not use liquid or aerosol cleaners.
• Place your product on a firm, solid surface. If you put it on something unsteady, it may fall and be damaged. If you place it on
a soft surface, such as a rug, sofa, or cushion, the vents may be blocked, causing the product to overheat.
• Protect your product from overheating. Make sure no obstructions block the openings of the product. Do not put the product
on or near a heat source (such as a radiator or heat register). Keep the product out of direct sunlight.
• Always use this product in a well ventilated area. Allow enough room around the product for adequate ventilation and easy
access to the paper trays. If you put the product in any kind of enclosure, make sure the enclosure is well ventilated.
• Do not use your product near water. Do not spill liquid of any kind into it.
• Be certain that your power source matches the rating listed on the back of the product. If you are not sure, check with your
dealer or with your local power company.
• Do not connect this product to an uninterruptible power supply (UPS).
• Your product has a grounded, three-prong plug as a safety feature. This plug only fits into a grounded outlet. If the plug does
not fit, the outlet may be an older, non-grounded type. Contact an electrician to have the outlet replaced. Do not use an
adapter to defeat the grounding.
• Install the product near an easily accessed power outlet.
• Avoid damaging the power cord. Do not put anything on it or place it where it will be walked on. If the cord becomes damaged
or frayed, replace it immediately.
• If you are using an extension cord or power strip with the product, make sure that the total of the amperes required by all the
equipment on the extension is less than the extension’s rating. The total ratings of all equipment plugged into the outlet
should not exceed 15 amperes.
• Do not poke anything into the ventilation slots of the product. You could get an electrical shock or cause hazardous electrical
arcing, which could cause a fire.
• Aside from the routine maintenance described in the documentation, do not try to service the product yourself. Removing the
cover may expose you to shocks or other hazards.
• Do not make any adjustments other than those outlined in the documentation. You may cause damage that will require
extensive repair work. The provided documentation explains how to get your product serviced by qualified iSys technicians. If
anything happens that indicates that your product is not working properly or has been damaged, unplug it immediately and
follow the procedures in the provided documentation for having your product serviced.
• Here are some of the things to look for.
• The power cord or plug is frayed or damaged.
• Liquid has been spilled into the product, or the product has been exposed to water.
• The product has been dropped, or the cabinet is damaged.
• The product does not function normally when you are following the operating instructions.
220/240-Volt Models
This product has been carefully designed to give years of safe, reliable performance. As with all electrical equipment, however,
there are a few basic precautions that should be taken to avoid injury or damage:
Ensure this and all other documentation is both read carefully and retained for future reference.
Ensure all warning and instruction labels on the product are read, understood and followed in order to prevent any
risk of injury.
This product may be heavy. Please check the weight of the product and take all necessary precautions to prevent
the risk of personal injury.
The product must be placed on a flat solid surface strong enough to support its weight to prevent any risk of injury.
Ensure that there is adequate ventilation all around the product to prevent overheating and any risk of fire.
Keep the product away from direct heat sources such as radiators and out of direct sunlight to prevent any risk of
overheating.
The power supply required for this product is 220-240 VAC, 50/60 Hz. (For any DC powered product, the figures are
9.6- 31.2VDC, 4-1.8A.) Refer to your product’s rating label on the machine for full power rating details. Ensure that