SBE HighWire HW400c/2 - Manual (Page 94)

HighWire HW400c/2 User Reference Guide Rev 1.0
TFTP from server 10.0.0.5; our IP address is 10.0.0.10
#########
###############
Bytes transferred = 1551015 (17aaa7 hex)
Entry
K
address 00000000) ...
gigateak_setup_peripherals: enter
gateak_intr_setup: exit
gateak_setup_arch: exit
c version 3.4.4 (Gentoo 3.4.4- r1,
V-643xx 10/100/1000 Ethernet Driver
led
Filename 'uImage'.
Load address: 0x400000
Loading: ########################################
##################################
#################################################
#################################################
###############################
done
## Booting image at 00400000 ...
Image Name: Linux-2.6.9
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1550951 Bytes = 1.5 MB
Load Address: 00000000
Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... O
## Transferring control to Linux (at
setup_arch: enter
setup_arch: bootmem
gigateak_setup_arch: enter
gigateak_setup_arch: calling setup_bridge
IGNP jumper is installed
Host PCI is not present
mv64x60 initialization
mv64x60 initialization done
gigateak_intr_setup: enter
gi
gigateak_setup_peripherals: exit
In gigateak_setup_ethernet
gi
arch: exit
mv64460_init_irq: enter
mv64460_init_irq: exit
Total memory = 256MB; using 512kB for hash table (at 80400000)
Linux version 2.6.9 (root@localhost) (gc
ssp-3.4.4-1.0, pie-8.7.8)) #2 Wed Apr 12 13:16:54 6PCI#1: first=0 last=0
SBE Gigateak HW400c/2 port
Built 1 zonelists
Kernel command line: console=ttyMM0,9600n9 ip=bootp nfsroot=/opt/gentoo
root=/dev/nfs rw
PID hash table entries: 2048 (order: 11, 32768 bytes)
time_init: decrementer frequency = 41.666666 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 255104k available (2388k kernel code, 1212k data, 128k init, 0k
highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
stered protocol family 16 NET: Regi
PCI: Probing PCI hardware
gigateak_map_irq 14F1:8474 slot=1 pin=1 irq=81
gigateak_map_irq 14F1:8474 slot=1 pin=2 irq=82
SCSI subsystem initialized
Installing knfsd (copyright (C) 1996 [email protected]).
Initializing Cryptographic API
MV64x60 watchdog driver
ipmi message handler version v33
ipmi device interface version v33
IPMI System Interface driver version v33, KCS version v33, SMIC version v33,
BT version v33
ipmi_si: Trying "kcs" at I/O port 0xca2
ipmi_si: Trying "smic" at I/O port 0xca9
ipmi_si: Trying "bt" at I/O port 0xe4
ipmi_si: Unable to find any System Interface(s)
IPMI Watchdog: driver version v33
Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot version
v33.
Serial: MPSC driver $Revision: 1.00 $
ttyMM0 at MMIO 0xf1008000 (irq = 36) is a MPSC
ttyMM1 at MMIO 0xf1009000 (irq = 38) is a MPSC
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
M
eth0: port 0 with MAC address 00:a0:d6:62:39:03
eth0: RX NAPI Enab
October 10, 2006 Copyright 2006, SBE, Inc. Page 82