Roland RS-70 - Manual (Page 126)

126
Settings common to all modes (System Function)
Settings related to controllers
(CONTROLLER)
Mod (Modulation Assign)
You can use the modulation lever to apply the following effects
other than vibrato.
In Patch mode, the modulation lever will affect the patch. In Pattern
mode, the modulation lever will affect the patch that is assigned to
the current part. Use [DESTINATION TONE] to specify the tone that
will be affected (p. 30).
“TxCC#” refers to the controller number of the control change
message sent from the MIDI OUT connector when the modulation
lever is operated. When set to AFTERTOUCH, Channel Aftertouch
messages are sent. Set to AFTERTOUCH mainly when you want to
control an external sound generator with Aftertouch messages.
Receiving these control change message from the MIDI IN connector
produces the same effect as operating the modulation lever.
* When set to MFX PARAMETER1 or MFX PARAMETER2, be sure
to note the following.
• When the multi-effects Type is set to 01: STEREO EQ (p. 95) or 42:
LOFI (p. 109), Level is changed regardless of whether MFX
PARAMETER1 or MFX PARAMETER2 is selected.
* When making the LFO RATE, LFO DEPTH or LFO DELAY settings,
the effect achieved differs depending on whether [FILTER LFO] is on or
off. When [FILTER LFO] is off, the LFO alters the pitch (vibrato
effect). When [FILTER LFO] is on, the LFO changes the Filter Cutoff
frequency (wah effect).
Pedal (Pedal Control Assign)
This specifies the function of the pedal connected to the CONTROL
PEDAL jack.
VALUE
In addition to the items listed in Modulation Assign, you can use the
pedal to apply the following effects.
PUNCH IN/OUT: Use the pedal to start or stop manual punch-in/
out recording (p. 69).
TAP TEMPO: Use the pedal to make tap tempo settings (p. 67).
C1 (C1 Knob Assign)
C2 (C2 Knob Assign)
C3 (C3 Knob Assign)
Select the effects that will be controlled by the [C1]/[C2]/[C3] knobs.
VALUE
In addition to the items listed in Modulation Assign, you can use the
pedal to apply the following effects.
PATCH MODIFY: The effect indicated on the panel will be
controlled (p. 30).
* If you assign any effects other than PATCH MODIFY to the [C1]/
[C2]/[C3] knobs, you must switch the Patch Modify select button
to [ENV] (envelope). If [BALANCE/LFO] is selected, the balance and
LFO will change.
* If you are using the [C1]/[C2]/[C3] knobs in Pattern mode to control
MFX PARAMETER settings, the “MFX Source” (p. 79) setting will
determine the part whose effect will be controlled.
If
MFX Source is set to “Part1–16,” the effect of that part will be
controlled.
If MFX Source is set to “PTN/PERF,” the System
“Ptn/Perf Ctrl Ch
(Pattern Control Channel)” (p. 127) setting will determine the part
whose effect will be controlled. If this setting is “OFF,” no effect will be
controlled.
Value Tx CC# Function/Parameter
Changed
MODULATION CC01 Vibrato
PORTA TIME CC05 Portamento Time (p. 58)
VOLUME CC07 Level
BALANCE CC08 The volume balance of LOW-
ER and UPPER tones (p. 56).
PAN CC10 Pan (p. 57)
EXPRESSION CC11 Level
PORTAMENTO CC65 Portamento Switch (p. 58)
SOSTENUTO CC66 Holds the sound of the key be-
ing pressed
SOFT CC67 Softens the tone
RESONANCE CC71 Tone Filter Resonance (p. 59)
RELEASE TIME CC72 Tone Envelope Release Time
(p. 59)
ATTACK TIME CC73 Tone Envelope Attack Time (p.
59)
CUTOFF CC74 Tone Filter Cutoff (p. 58)
DECAY TIME CC75 Tone Envelope Decay Time (p.
59)
LFO RATE CC76 Tone LFO Rate (p. 58)
LFO DEPTH CC77 Tone LFO Depth (p. 58)
LFO DELAY CC78 Tone LFO Delay (p. 58)
CHO SEND LEVEL CC93 Chorus Send Level (p. 57)
REV SEND LEVEL CC91 Reverb Send Level (p. 57)
MFX PARAMETER1 CC12 The parameter specified by
Multi-effect Control 1 (p. 95)
MFX PARAMETER2 CC13 The parameter specified by
Multi-effect Control 2 (p. 95)
AFTERTOUCH ----
RS-70_e3.book 126 ページ ２００３年６月１８日 水曜日 午後１２時５４分