Roland RS-70 - Manual (Page 77)

77
Using the sequencer to create patterns (Pattern mode)
Pattern Mode
Ch Aft (Channel Aftertouch)
These events apply aftertouch to each MIDI channel.
Value: 0–127
Channel aftertouch is data transmitted for an entire channel to
indicate the force with which the keys are being pressed down
after notes are played. The RS-70’s keyboard is not able to
transmit channel aftertouch, but you can assign channel
aftertouch transmission to a controller such as a knob or pedal,
and record these messages.
PitchBend
These events change the pitch.
Value: -8192–+8191
TUNE (Tune Request)
This event causes an analog synthesizer to tune itself. This does not
affect the operation of the RS-70 itself.
SYS-EX (System Exclusive messages)
These are events unique to the RS-70. If the entire message cannot be
shown on one line, a “ ” will appear at the right edge of the
display.
You can use PAGE/CURSOR [ ]/[ ] to scroll the display
screen.
Editing the music data
If you want to edit system exclusive messages, refer to
“Modifying system exclusive data” (p. 77).
1. Select a pattern you want to edit.
2. While holding down [SHIFT], press [ ].
The Microscope screen will appear.
3. Use [0]–[9] to select the part that you want to edit.
To select the parts 11–16, hold down [SHIFT] and press [1]–[6]
(p. 54).
4. Use PAGE/CURSOR [ ]/[ ] to move the cursor under the
location (measure-beat-clock) and use VALUE [-]/[+] to move
the location forward or back.
The type and value of the event recorded at that location will be
displayed.
You can also use [ ]/[ ] to move the current location a
measure at a time, without regard to the cursor position.
fig.r06-45.e_40
If you want to display a clock location at which no event is
recorded (such as when you want to add an event), move the
cursor to the clock and press [NUMERIC] so it is lit. Use [0]–[9]
to specify the desired value, then press [ENTER].
5. Press PAGE/CURSOR [ ] to move the cursor under the
event and use VALUE [-]/[+] to modify its value.
Modifying system exclusive data
1. In the above step 4., select the system exclusive message
that you wish to modify.
fig.r06-46
2. Press PAGE/CURSOR [ ].
The system exclusive input page will appear.
Press PAGE/CURSOR [ ] move the cursor to the location that
you wish to modify. (You cannot choose “F0” or “F7.”)
You can hold down [SHIFT] and use PAGE/CURSOR [ ]/
[ ] to move the cursor to the beginning or end of the exclusive
data.
3. Input the value.
• To input a value: press VALUE [-]/[+] or [0]–[9].
• To input A–F: hold down [SHIFT] and press [0] (A)–[5] (F).
• To insert a value midway: move the cursor to that location, and
press [ ]. A value of “00” will be inserted, and you can modify
this to the desired value.
• To delete a value: move the cursor to that location, and press
[ERASE/UNDO].
4. Press [ENTER], and the modified settings will be finalized.
If you decide to cancel, press [EXIT].
Auto calculate checksum
While editing an exclusive message, you can press [PARAM] to set it
so the checksum is calculated automatically.
If this setting is “ON,” and you press [ENTER] after editing the
message, the checksum will be calculated automatically, and
inserted before the last byte (F7) of the message.
fig.r06-47_40
This setting will always be ON when you turn on the power.
location (measure-beat-clock)
symbol indicates that other MIDI messages exist
at the same location
message parameters
RS-70_e3.book 77 ページ ２００３年６月１８日 水曜日 午後１２時５４分