TANDBERG TT1260 - Manual (Page 154)

Index
Index-4 Instruction Manual: TT1260 Standard Definition Professional Receiver/Decoder
ST.TM.E10100.1
operation modes, 3-5
setting up preset service, 3-17
preset services
preset menu (#1) pages, C-5
setting up, 3-17
programme delivery and control (PDC), 1-7
PSU. See power supply
Q
QPSK input card, 5-4
quick reference guide
loading a preset service, G-5
setting up a preset service, G-5
setting up a satellite receiver, G-3
setting up a service, G-4
setting up the service hunt mode, G-4
R
rack mounting standard, B-19
RAS mode 1 CA software key, 5-9
rear panel
S12316 alarm relay card:, 2-15
S12495 ASI input card, 5-4
S12496 QPSK input card, 5-5
S12501 8PSK/16QAM card:, 5-7
S12595 high speed RS-422 data enabler card, 5-7, 5-8
view, 1-17
Reed-Solomon decoding, 1-11
remote authorisation system (RAS 1), 1-17
remote authorisation system (RAS), 1-7, 1-9, 3-13
RAS1, 3-13
RAS2, 3-13
remote control
connector, 2-13, B-17, B-18
fault-finding, 6-5
NCP, 1-7
summary, 1-7
restarting the unit, 3-17
RS-232
remote control, 2-13
RS-422 data enabler card, 5-7
RS-485
remote control, 2-13
S
S12316 alarm relay card
connectors, 2-15
rear panel view, 2-15
S12495 ASI input card
connectors, 5-4
rear panel view, 5-4
S12496 QPSK input card
connectors, 5-5
rear panel view, 5-5
S12501 8PSK/16QAM card
connectors, 5-7
rear panel view, 5-7
S12595 high speed RS-422 data enabler card
connectors, 5-7, 5-8
rear panel view, 5-7, 5-8
safety, B-21
ac supply operating voltage and fusing information, 2-5
BS 60950 compliance statement, B-21
disposal of moulded plugs, 6-7
handling and installation, 2-3
IEC 950 compliance statement, B-21
lack of equipment on/off switch, 2-6
lightning protection, 1-8, 5-5
moisture, 2-5
moving the equipment, 2-3
wallsocket overloading, 2-6
satellite receiver
input attenuator, 5-5
input QPSK specification, B-10, B-12
input summary, 1-11
QPSK L-band (#n) connector, B-10, B-12
QPSK L-band connector, 5-5
setting up the input, 3-8, G-3
typical system, 1-10
satellite receivers
main features, 1-5
selecting
a service, 3-9, G-4
selecting menu options, 3-7
services
selecting, 1-6, 3-9, G-4
setting up presets, 3-17
servicing
checks on completion, 6-4
damage indicating a requirement., 6-3
replacement parts \b, 6-4
setting up
alarms, 3-16
async/sync data, 3-11
decoder, 3-8
satellite receiver, 3-8
system, 3-16
teletext, 3-12
transport stream, 3-15
VBI, 3-12
signal connections, 2-8
motherboard
alarm, 2-13
ASI out, 2-10
audio, 2-10
CVBS, 2-11
frame sync hi-z, 2-12
RS232 async data, 2-14
SDI, 2-11
signal protection CA software key, 5-9
smart card, 1-15
SMPTE 302M-1998, B-8
software download. See over-air software download
software keys
TT1260/SWO/16QAM, 5-9
TT1260/SWO/8PSK, 5-9
TT1260/SWO/BISS, 5-10
TT1260/SWO/DIR, 5-10
TT1260/SWO/RAS, 5-9
TT1260/SWO/SP, 5-9
software reboot, 3-17
software version
covered by this manual, 1-4
software version front panel display, 3-17
specification
8PSK/16QAM card, 5-7
alarm relay card, 2-15
ASI input card, 5-4
audio analogue output, B-9
audio digital output, B-9
data RS-232, B-17
EN 300 421, 1-6
EN 301 210, 1-6
frame sync connector, 2-12, B-15
high speed RS-422 data enabler card, 5-8
ISO 13818, 1-6
low-noise block, B-11
power supply, B-19