Speaker setup, Adjusting the dvd level, Linear pcm setting – Alpine INA-W910 User Manual

Page 82: Storing settings in the memory, Calling up the preset memory, Adjusting the dvd level linear pcm setting

Advertising
background image

82

-EN

Adjusting the speaker levels (Output Level)

The test tones help to make the volume adjustments of the
different speakers. When levels are equal, a strong sense of
presence can be heard from the different speakers at the
listening position.

Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the decode mode is switched.

1 Touch [On] of Output Level.

Test tone output is repeated for each of the different speaker
channels. They will be repeated in the order shown below.
If no operation is performed for 2 seconds, the channel
switches to the next channel.

2 While the test tone is being produced from the speakers,

touch [

] or [

] of Output Level balance the output from all

the speakers.

3 Touch [On] again to turn off.

If a speaker is set to off mode, that speaker’s level adjustment cannot

be made. Refer to “Speaker Setup” (page 82).

The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).

Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this
adjustment. The setting is canceled if Decode mode is switched.

Setting item: Speaker Setup

Select the speaker characteristic by touching [

], [

]

of the desired speaker setting.

*

1

It is not possible to set the front speakers to “OFF”.

*

2

If the front speakers are set to “Small”, the rear and center speakers
cannot be set to “Large”.

The subwoofer can be set only to ON/OFF.
If the center speaker is turned “OFF”, the center channel’s audio

signals are added to the audio signals output from the front speakers.

If you set the speaker response to “OFF”, also set the speaker setting

to “OFF” (page 81).

Perform the setup for all the speakers (“Front”, “Center” ,“Rear”

and “Subwoofer”). If not, the sound may not be balanced.

When center is set to “OFF”, the setting is ineffective even if center

is set with this function.

Through changing the settings on each speaker, a change in the

output of the other speakers may occur due to the setting
requirements.

When using the PRO Logic II, if the rear speaker is set to “Large”,

then there will be no output from the subwoofer.

The volume (signal level) for Dolby Digital, Dolby PL II, DTS and
PCM modes can be set.

Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.

Setting item: DVD Level

Adjust the level by touching [

] or [

] of the desired

adjusting mode.

The output when playing discs recorded in linear PCM can be set to 2 or
3 channels.

Setting item: PCM Mode

Touch [

] or [

] of PCM Mode to select 2CH or 3CH.

This adjustment is ineffective when the speaker is set Center to OFF

in “Setting the Speakers” (page 81).

Storing Settings in the Memory

Adjustment or setting contents can be stored.
Contents that can be stored vary depends on the audio processor used.

1

Touch [MEMORY] on the A.Processor list display.

2

Within 5 seconds, touch any one of the preset
buttons [P.SET 1] through [P.SET 6] on the
A.Processor list screen.

The setting contents are stored.

The stored contents will not be deleted even when the battery power

cord is detached.

Calling up the Preset Memory

Touch any one of the preset buttons [P.SET 1] through
[P.SET 6] on the A.Processor list display to select the
preset memory.

It takes a few moments to call up the preset memory.

Left

Center

Right

Right Surround

Left Surround

Left

The adjustment range for the different speakers is -10 dB ~ +10 dB.
Adjust based on the front speakers.

Speaker Setup

OFF

*

1

:

When no speaker is connected.

Small:

When a speaker that cannot play low frequencies
(80 Hz or less) is connected.

Large

*

2

:

When a speaker that can play low frequencies

(80 Hz or less) is connected.

Adjusting the DVD Level

Linear PCM Setting

2CH: 2ch output (L/R)

3CH: 3ch output (L/R/CENTER)

Advertising