AMD Geode SC1201 - Manual (Page 277)

AMD Geode™ SC1200/SC1201 Processor Data Book 277
Core Logic Module - X-Bus Expansion Interface - Function 5 32579B
6.4.5 X-Bus Expansion Interface - Function 5
The register space designated as Function 5 (F5) is used
to configure the PCI portion of support hardware for
accessing the X-Bus Expansion support registers. The bit
formats for the PCI Header Registers are given in Table 6-
39. Located in the PCI Header Registers of F5 are six Base
Address Registers (F5BARx) used for pointing to the regis-
ter spaces designated for X-Bus Expansion support,
described later in this section.
Table 6-39. F5: PCI Header Registers for X-Bus Expansion
Bit Description
Index 00h-01h Vendor Identification Register (RO) Reset Value: 100Bh
Index 02h-03h Device Identification Register (RO) Reset Value: 0505h
Index 04h-05h PCI Command Register (R/W) Reset Value: 0000h
15:2 Reserved. (Read Only)
1 Memory Space. Allow the Core Logic module to respond to memory cycles from the PCI bus.
0: Disable.
1: Enable.
If F5BAR0, F5BAR1, F5BAR2, F5BAR3, F5BAR4, and F5BAR5 (F5 Index 10h, 14h, 18h, 1Ch, 20h, and 24h) are defined as
allowing access to memory mapped registers, this bit must be set to 1. BAR configuration is programmed through the corre-
sponding mask register (see F5 Index 40h, 44h, 48h, 4Ch, 50h, and 54h)
0 I/O Space. Allow the Core Logic module to respond to I/O cycle from the PCI bus.
0: Disable.
1: Enable.
If F5BAR0, F5BAR1, F5BAR2, F5BAR3, F5BAR4, and F5BAR5 (F5 Index 10h, 14h, 18h, 1Ch, 20h, and 24h) are defined as
allowing access to I/O mapped registers, this bit must be set to 1. BAR configuration is programmed through the corre-
sponding mask register (see F5 Index 40h, 44h, 48h, 4Ch, 50h, and 54h)
Index 06h-07h PCI Status Register (RO) Reset Value: 0280h
Index 08h Device Revision ID Register (RO) Reset Value: 00h
Index 09h-0Bh PCI Class Code Register (RO) Reset Value: 068000h
Index 0Ch PCI Cache Line Size Register (RO) Reset Value: 00h
Index 0Dh PCI Latency Timer Register (RO) Reset Value: 00h
Index 0Eh PCI Header Type (RO) Reset Value: 00h
Index 0Fh PCI BIST Register (RO) Reset Value: 00h
Index 10h-13h Base Address Register 0 - F5BAR0 (R/W) Reset Value: 00000000h
X-Bus Expansion Address Space. This register allows PCI access to I/O mapped X-Bus Expansion support registers. Bits [5:0] must
be set to 000001, indicating a 64-byte aligned I/O address space. Refer to Table 6-40 on page 281 for the X-Bus Expansion configura-
tion register bit formats and reset values.
Note: The size and type of accessed offsets can be reprogrammed through F5BAR0 Mask Register (F5 Index 40h).
31:6 X-Bus Expansion Base Address.
5:0 Address Range. This bit field must be set to 000001 for this register to operate correctly.
Index 14h-17h Base Address Register 1 - F5BAR1 (R/W) Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR1 Mask Register (F5 Index 44h)
Index 18h-1Bh Base Address Register 2 - F5BAR2 (R/W) Reset Value: 00000000h
Reserved. Reserved for possible future use by the Core Logic module.
Configuration of this register is programmed through the F5BAR1 Mask Register (F5 Index 48h)