AMD Geode SC1201 - Manual (Page 72)

72 AMD Geode™ SC1200/SC1201 Processor Data Book
General Configuration Block 32579B
4.2 Pin Multiplexing, Interrupt Selection, and Base Address Registers
The registers described in Table 4-2 are used to determine
general configuration for the SC1200/SC1201 processor.
These registers also indicate which multiplexed signals are
issued via balls from which more than one signal may be output. For more information about multiplexed signals and
the appropriate configurations, see Section 3.1 "Ball
Assignments" on page 27.
Table 4-2. Pin Multiplexing, Interrupt Selection, and Base Address Registers
Bit Description
Offset 30h-33h Pin Multiplexing Register - PMR (R/W) Reset Value: 00000000h
This register configures pins with multiple functions. See Section 3.1 on page 27 for more information about multiplexing information.
31:30 Reserved: Always write 0.
29 Test Signals. Selects ball functions.
Ball # 0: Internal Test Signals 1: Internal Test Signals
Name Add’l Dependencies Name Add’l Dependencies
D28 / AH3 PLL2B None TEST0 None
C28 / AG4 PLL6B None TEST1 None
B29 / AJ1 PLL5B None TEST2 None
AL16 / V30 GXCLK See PMR[23] TEST3 PMR[23] = 0
28 Test Signals. Selects ball function.
Ball # 0: AC97 Signal 1: Internal Test Signal
Name Add’l Dependencies Name Add’l Dependencies
AJ4 / E28 SIN2 None SDTEST3 See Note.
Note: If this bit is set, PMR[8] and PMR[18] must be set by software.
27 FPCI_MON (Fast-PCI Monitoring). Selects Fast-PCI monitoring output signals instead of Parallel Port signals.
Fast-PCI monitoring output signals can be enabled in two ways: by setting this bit to 1 or by strapping FPCI_MON (ball A4)
high. (The strapped value can be read back at MCR[30].) Listed below is how these two options work together and the sig-
nals that are enabled (enabling overrides add’l dependencies except FPCI_MON = 1). Note that the FPCI monitoring signals
that are muxed with Audio signals are not enabled via this bit. They are only enabled using the strap option.
PMR[27] FPCI_MON
0 0 Disable all Fast-PCI monitoring signals
0 1 Enable all Fast-PCI monitoring signals
1 0 Enable Fast-PCI monitoring signals muxed with Parallel Port signals only
1 1 Enable all Fast-PCI monitoring signals
Ball #
FPCI_MON Other Signal Add’l Dependencies
U3 / B18 FPCICLK ACK#+TFTDE+VOPCK See PMR[23]
U1 / A18 F_AD7 PD7+TFTD13 See PMR[23]
V3 / A20 F_AD6 PD6+TFTD1+VOPCK See PMR[23]
V2 / C19 F_AD5 PD5+TFT11 See PMR[23]
V1 / C18 F_AD4 PD4+TFTD10 See PMR[23]
W2 / C20 F_AD3 PD3+TFTD9 See PMR[23]
W3 / D20 F_AD2 PD2+TFTD8+VOPD7 See PMR[23]
Y1 / A21 F_AD1 PD1+TFTD7+VOPD6 See PMR[23]
AA1 / C21 F_AD0 PD0_TFTD5+VOPD6 See PMR[23]
T4 / C17 F_C/BE3# SLCT+TFTD15 See PMR[23]
T3 / D17 F_C/BE2# PE+TFTD14 See PMR[23]
T1 / B17 F_C/BE1# BUSY/WAIT#+TFTD3+VOPD2 See PMR[23]
AA3 / D21 F_C/BE0# ERR#+TFTD4+VOPD3 See PMR[23]
AB1 / A22 F_FRAME# STB#/WRITE#+TFTD7 See PMR[23]
W1 / B20 F_IRDY# SLIN#/ASTRB#+TFTD16 See PMR[23]
AB2 / D22 INTR_O AFD#/DSTRB#+TFTD2+VOPD1 See PMR[23]
Y3 / B21 SMI_O INIT#+TFTD5+VOPD4 See PMR[23]
AL15 / V31 F_DEVSEL# GPIO16+PC_BEEP FPCI_MON = 1 and see PMR[0]
AJ15 / U29 F_STOP# AC97_RST# FPCI_MON = 1
AK14 / U31 F_GNT0# SDATA_IN FPCI_MON = 1
AL14 / U30 F_TRDY# BIT_CLK FPCI_MON = 1
26 Note: Reserved: Always write 0.