Document Outline

• Chapter 1: Safety Information
  • 1.1. Warnings
  • 1.2. Cautions
  • 1.3. Directives and Standards
  • 1.4. CE Marking Conformance
  • 1.5. Warranty Information
• Chapter 2: Product Description
  • 2.1. Functional Description
  • 2.2. Product Features
    • 2.2.1. High Power Density
    • 2.2.2. Supply Input
    • 2.2.3. Servo Control
    • 2.2.4. Advanced Filters and Gain Scheduling
    • 2.2.5. Motion Control
    • 2.2.6. Fully Programmable
    • 2.2.7. Feedback Ports Options
    • 2.2.8. Feedback Sensor Specifications
    • 2.2.9. Communications
    • 2.2.10. Safety
    • 2.2.11. Outputs
    • 2.2.12. Inputs
    • 2.2.13. Built-In Protection
    • 2.2.14. Status Indication
    • 2.2.15. Automatic Procedures
  • 2.3. System Architecture
  • 2.4. How to Use this Guide
• Chapter 3: Technical Information
  • 3.1. Technical Data
    • 3.1.1. Auxiliary Supply
  • 3.2. Environmental Conditions
• Chapter 4: Installation
  • 4.1. Site Requirements
  • 4.2. Unpacking the Drive Components
  • 4.3. Connectors
    • 4.3.1. Connector Types
    • 4.3.2. Pinouts
      • 4.3.2.1. Motor Power
      • 4.3.2.2. Main Power
      • 4.3.2.3. Auxiliary Power Connector
      • 4.3.2.4. Connector J2
      • 4.3.2.5. Connector J1
  • 4.4. Mounting the Gold Hawk
  • 4.5. Integrating the Gold Hawk on a PCB
    • 4.5.1. Grounds and Returns
  • 4.6. The Gold Hawk Connection Diagram
  • 4.7. Main Power, Auxiliary Power and Motor Power
    • 4.7.1. Motor Power
    • 4.7.2. Main Power, Motor Power and Auxiliary Power
      • 4.7.2.1. Motor Power
      • 4.7.2.2. Main Power
    • 4.7.3. Auxiliary Power Supply (Optional)
    • 4.7.4. Single Supply
    • 4.7.5. Separate Auxiliary (Backup) Supply
    • 4.7.6. Shared Supply
  • 4.8. STO (Safe Torque Off) Inputs
  • 4.9. Feedback
    • 4.9.1. Port A (J2)
      • 4.9.1.1. Incremental Encoder
      • 4.9.1.2. Absolute Serial Encoder
      • 4.9.1.3. Hall Sensors
    • 4.9.2. Port B (J2)
      • 4.9.2.1. Incremental Encoder
      • 4.9.2.2. Interpolated Analog Encoder
      • 4.9.2.3. Resolver
    • 4.9.3. Port C – Emulated Encoder Output (J2)
    • 4.9.4. Analog Input
  • 4.10. User I/Os
    • 4.10.1. Digital Inputs (J1)
    • 4.10.2. Digital Outputs (J1)
    • 4.10.3. Analog Input
  • 4.11. Communications
    • 4.11.1. RS-232 Communication (J2)
    • 4.11.2. CAN Communication (J2)
    • 4.11.3. USB 2.0 Communication (J2)
    • 4.11.4. EtherCAT Communication (J2)
    • 4.11.5. Ethernet Communication (J2)
    • 4.11.6. EtherCAT/Ethernet Line Interface
  • 4.12. Powering Up
  • 4.13. Initializing the System
  • 4.14. Heat Dissipation
    • 4.14.1. Thermal Data
    • 4.14.2. Heat Dissipation Data
    • 4.14.3. How to Use the Charts
• Chapter 5: Technical Specifications
  • 5.1. Dimensions
  • 5.2. Control Specifications
    • 5.2.1. Current Loop
    • 5.2.2. Velocity Loop
    • 5.2.3. Position Loop
  • 5.3. Feedbacks
    • 5.3.1. Feedback Supply Voltage
    • 5.3.2. Feedback Options
      • 5.3.2.1. Incremental Encoder Input
      • 5.3.2.2. Digital Halls
      • 5.3.2.3. Interpolated Analog (Sine/Cosine) Encoder
      • 5.3.2.4. Resolver
      • 5.3.2.5. Absolute Serial Encoder
    • 5.3.3. Port C Feedback Output
  • 5.4. I/Os
    • 5.4.1. Digital Input Interfaces – TTL Mode
    • 5.4.2. Digital Output Interface – TTL Mode
      • 5.4.2.1. OUT1 and OUT2
      • 5.4.2.2. OUT3 and OUT4
    • 5.4.3. Analog Input
  • 5.5. Safe Torque Off (STO)
    • 5.5.1. STO Input Interfaces – TTL Mode
  • 5.6. Communications
  • 5.7. Pulse-Width Modulation (PWM)
• Chapter 6: Gold Line Standards
  • 6.1. Functional Safety
  • 6.2. Safety
  • 6.3. EMC
  • 6.4. EtherCAT Conformance
  • 6.5. Other Compliant Standards
  • 6.6. ExtrIQ Series