Barco R9001330 - Manual (Page 17)

Safety Instructions
5975288 BARCOGRAPHICS 8200 110497 1-11
Safety Instructions
5975288 BARCOGRAPHICS 8200 110497 1-11
* Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On Servicing
Do not attempt to service this projector yourself, as opening or
removing covers may expose you to dangerous voltage potential and
risk of electric shock! Refer all projector service to a qualified BARCO
service center.
Call for service in the following conditions :
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the projector.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating
instructions are followed.
Adjust only those controls that are covered by the operating i n -
structions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation;
- If the product has been dropped or the cabinet has been damaged;
- If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts
or authorized replacement parts which have the same characteris-
tics as the BARCO original part. Unauthorized substitutions may
result in degraded performance and reliability, fire, electric shock or
other hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the projector is in proper operating condition.
The projecor uses a metal halide projection lamp. Replacing the
projection lamp with any other projection lamp can cause overheat-
ing or unacceptable image quality. Use only the projection lamps
specified by BARCO, or an authorized BARCO dealer or service
center.
On Cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft
cloth. Stubborn stains may be removed with a cloth lightly dampened
with mild detergent solution. Never use strong solvents, such as
thinner or benzine, or abrasive cleaners, since these will damage the
cabinet.
* Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On Servicing
Do not attempt to service this projector yourself, as opening or
removing covers may expose you to dangerous voltage potential and
risk of electric shock! Refer all projector service to a qualified BARCO
service center.
Call for service in the following conditions :
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the projector.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating
instructions are followed.
Adjust only those controls that are covered by the operating i n -
structions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation;
- If the product has been dropped or the cabinet has been damaged;
- If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts
or authorized replacement parts which have the same characteris-
tics as the BARCO original part. Unauthorized substitutions may
result in degraded performance and reliability, fire, electric shock or
other hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the projector is in proper operating condition.
The projecor uses metal halide projection lamp. Replacing the
projection lamp with any other projection lamp can cause overheat-
ing or unacceptable image quality. Use only the projection lamps
specified by BARCO, or an authorized BARCO dealer or service
center.
On Cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft
cloth. Stubborn stains may be removed with a cloth lightly dampened
with mild detergent solution. Never use strong solvents, such as
thinner or benzine, or abrasive cleaners, since these will damage the
cabinet.