Barco R9001330 - Manual (Page 37)

Location and Functions of Control
5975288 BARCOGRAPHICS 8200 110497 5-5
Location and Functions of Control
5975288 BARCOGRAPHICS 8200 110497 5-5
Terminology
Back light key : when activated, all keys will be lighted up
and visible in the dark.
ADJ. : ADJUST key, to enter the adjustment mode or for
quick exit in the adjustment mode.
A ddress key (sunk key), to enter the address of the projec-
tor (between 0 and 9). Press the sunk address key with a
pencil, followed by pressing one digit button between 0 and
9.
STBY : stand by button - to start projection when the
power switch is switched on.
- to switch off the projector
without switching off the power switch.
PAUSE : to stop projection for a short time, press 'PAUSE'.
The image disappears but full power is retained for imme-
diate restarting.
HELP : on line help information.
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
picture analog level (see also 'Controlling').
PHASE : used to remove the instability of the image.
TEXT : when adjusting one of the image, e.g. controls
during a meeting, the displayed bar scale can be removed
by pressing 'TEXT' key first. To re-display the bar scale on
the screen, press 'TEXT' key again. 'TEXT' key only active
in operational mode.
FREEZ : press to freeze the projected image.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control disk (on RCU) or '+' and '-' keys (cursor keys): to
make menu selections when in the adjustment mode.
The control disk can move up, down, to the right or to the
left.
Comparision between control disk movement and the use
of the cursor keys on the local keypad :
RCU
= local keypad
control disk up = '+' key up
control disk down = '-' key down
control disk to the right = '+' key right
control disk to the left = '-' key left
Use the '+' and '-' keys (cursor keys) : to increase or
decrease the analog level of the image controls when they
are first selected.
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
1
2
3
4
5
6
7
8
9
10
12
11
13
14
15
Terminology
Back light key : when activated, all keys will be lighted up
and visible in the dark.
ADJ. : ADJUST key, to enter the adjustment mode or for
quick exit in the adjustment mode.
A ddress key (sunk key), to enter the address of the projec-
tor (between 0 and 9). Press the sunk address key with a
pencil, followed by pressing one digit button between 0 and
9.
STBY : stand by button - to start projection when the
power switch is switched on.
- to switch off the projector
without switching off the power switch.
PAUSE : to stop projection for a short time, press 'PAUSE'.
The image disappears but full power is retained for imme-
diate restarting.
HELP : on line help information.
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
picture analog level (see also 'Controlling').
PHASE : used to remove the instability of the image.
TEXT : when adjusting one of the image, e.g. controls
during a meeting, the displayed bar scale can be removed
by pressing 'TEXT' key first. To re-display the bar scale on
the screen, press 'TEXT' key again. 'TEXT' key only active
in operational mode.
FREEZ : press to freeze the projected image.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control disk (on RCU) or '+' and '-' keys (cursor keys): to
make menu selections when in the adjustment mode.
The control disk can move up, down, to the right or to the
left.
Comparision between control disk movement and the use
of the cursor keys on the local keypad :
RCU
= local keypad
control disk up = '+' key up
control disk down = '-' key down
control disk to the right = '+' key right
control disk to the left = '-' key left
Use the '+' and '-' keys (cursor keys) : to increase or
decrease the analog level of the image controls when they
are first selected.
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to
check the operation of the remote control)
1
2
3
4
5
6
7
8
9
10
12
11
13
14
15