Connections, Video/s-video input module – Barco R9001330 User Manual
Page 44
Connections
Connections
5975288 BARCOGRAPHICS 8200 110497
7-3
7-3
5975288 BARCOGRAPHICS 8200 110497
Video/S-video input module
To the Video input :
Composite video signals from a VCR, OFF air signal decoder, etc...
1 x BNC 1.0Vpp ± 3 dB
To the S-Video input :
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS-signals.
1 x 4 pins plug (mini DIN)
pin configuration :
1
ground luminance
2
ground chrominance
3
luminance 1.0 Vpp ± 3 dB
4
chrominance 282 mVpp ± 3 dB
Input selection :
98 2790
A U D I O
VID EO/S-VIDEO IN PUT
O n
O n
Video input
Audio input not
available
S-Video input
TV tu ner, e.g .
TVD M 4 0 ste re o
V C R
A u d io a m p lif ie r
C o m p o s i t e
V i d e o
R
G
R
G
V C R S - V H S
L u m a / C h r o m a
RS 23 2 IN
1 00 - 2 3 0 V
9 - 4 A
6 0 - 50 Hz
R S2 32 O U T
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not c ause harmful interference
(2) This device must accept any interference received
including interference that m ay cause undesired operation
IR - A CK NO W LE DG ED
IR - REC EIV ED
D I A G N O S T I C S
C O D E
IR - R ECE IV ER
Key in the corresponding slot number on the RCU or the local
keypad. Depending on the priority setting in the Input slots
menu, Video or S-Video will be displayed. If the wrong
source type is displayed, start up the adjustment mode and
select Installation. Select the Input Slots menu. Highlight the
corresponding slot number with the control disk and press
ENTER
to change the priority setting. To start up the
Adjustment menu, press
ADJUST
or
ENTER
.
Video/S-video input module
To the Video input :
Composite video signals from a VCR, OFF air signal decoder, etc...
1 x BNC 1.0Vpp ± 3 dB
To the S-Video input :
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS-signals.
1 x 4 pins plug (mini DIN)
pin configuration :
1
ground luminance
2
ground chrominance
3
luminance 1.0 Vpp ± 3 dB
4
chrominance 282 mVpp ± 3 dB
Input selection :
98
27
A U D I O
VID EO/S-VIDEO IN PUT
O n
O n
Video input
Audio input not
available
S-Video input
TV tu ner, e.g .
TVD M 4 0 ste re o
V C R
A u d io a m p lif ie r
Com pos i t e
V id e o
R
G
R
G
V C R S - V H S
L u m a / C h r o m a
RS 23 2 IN
1 00 - 2 3 0 V
9 - 4 A
6 0 - 50 Hz
R S2 32 O U T
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not c ause harmful interference
(2) This device must accept any interference received
including interference that m ay cause undesired operation
IR - A CK NO W LE DG ED
IR - REC EIV ED
D I A G N O S T I C S
C O D E
IR - R ECE IV ER
Key in the corresponding slot number on the RCU or the local
keypad. Depending on the priority setting in the Input slots
menu, Video or S-Video will be displayed. If the wrong
source type is displayed, start up the adjustment mode and
select Installation. Select the Input Slots menu. Highlight the
corresponding slot number with the control disk and press
ENTER
to change the priority setting. To start up the
Adjustment menu, press
ADJUST
or
ENTER
.