In case of difficulty, Remote control unit – Kenwood UD-952 User Manual
Page 77
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
In case of difficulty
Remote control unit
$ymp^tom
Remedy
Remote control operation is not possible.
• Batteries are exhausted.
• Replace with new batteries.
• The remote control is too far apart from the
• Operate the unit inside the remote control
system, the controlling angle is deviated or
there is an obstacle in between.
lable range.
• The parallel cord is not connected properly.
• Connect properly referring to "Connec
tions".
• There is no tape or CD set in the component
• Set a tape or CD in the component to be
to be played.
played.
• An attempt is made to play the cassette deck
which is recording something.
• Wait until the recording ends.
• The A/B switch is not set properly.
• Set the A/B switch properly.
Preamplifier/tuner unit, power amplifier/graphic equalizer unit, speakers
___.^Symptom ^ ^
Remedy
Sound is not produced.
• The speaker cords are disconnected.
• The volume control is set to the minimum
position.
• The MUTE switch of the preamplifier/tuner
unit is switched ON.
• The headphone plug is inserted into the jack.
• The parallel cord is not connected.
• Connect properly referring to "Connec
tions".
• Adjust to an optimum volume.
• Switch MUTE OFF.
• Unplug the headphone plug.
• Check the connection of the parallel cord.
Sound is not produced from the main
speakers.
• The LINEAR ACOUSTIC CONTROL is set inad
equately.
• The speaker cords are disconnected.
• Adjust the control properly.
• Connect properly referring to "Connec
tions".
Sound is not produced through head
phones.
• The LINEAR ACOUSTIC CONTROL is set in
adequately.
• The sound is played through the SUB (OMNI)
input.
• Adjust the control properly. »
• Play it through the MAIN input.
Environmental sound cannot be played.
• The DUAL SOUND is OFF (indicator not lit).
• The LINEAR ACOUSTIC CONTROL is set in
adequately.
• Press the DUAL SOUND key to ON.
• Adjust the control properly.
The STAND BY indicator biinks and sound
is not produced.
• The speaker cords are short-circuited.
• Turn the power OFF, remove the short-cir
cuit and turn the power ON again.
Sound is not produced from the ieft or
right speakers.
• The speaker cords are disconnected.
• The BALANCE set inadequately.
• Connect properly referring to "Connec
tions".
• Adjust the optimum left and right balance.
-Ea
Sound is not produced from the surround
rear speakers or center speaker, or their
voiumes are very low.
• The rear speaker cords are disconnected.
• The surround play mode is not activated.
• The rear or center volume is set to the mini
mum level.
• Connect properly referring to "Connec-
tions".
• Activate a surround mode.
• Adjust the rear level. -►
The clock display blinks without changing
the figures.
• There was a power failure.
• The power cord was unplugged from the
outlet.
• Adjust the present time again.
• Adjust the present time again.
Timer operation is not possibie.
• The present time has not been adjusted or
there was a power failure.
• The timer ON time and OFF time have not
been set,
• The timer execution was not set up.
• Adjust the present time referring to "Clock
adjustment".
• Set the timer ON time and OFF time.
• Press the EXE key to set the execution.
Remedy
Sound is distorted.
• The recording level has not been set with the
• Refer to "Recording."
CRLS key.
• The tape being played was recorded with dis
• Try another tape.
torted sound.
Noise is noticeable.
• The tape head is magnetized.
• Demagnetize the head referring to "Head