LINK Systems OmniLink II Press Automation Control - Manual (Page 3)

August 30, 2002 Manual Version 1.0 ii
Section 4.2.1.8 Setting Brake Monitor Top Stop and Brake Monitor Mid Stroke Stop Limits ................................4.13
Section 4.2.2 Speed/Load Configuration Menu Settings...............................................................................................4.14
Section 4.2.2.1 Setting Speed Mode.........................................................................................................................4.15
Section 4.2.2.2 Calibrating Variable Speed Drive Input SPM When “Input Only” is Selected ...............................4.16
Section 4.2.2.3 Calibrating Variable Speed Drive Input SPM When Output Without Recall or Output With Recall is
Selected for Speed Mode..........................................................................................................................................4.17
Section 4.2.2.4 Calibrating the Analog Output SPM Signal to Give Correct Drive Speed ......................................4.17
Section 4.2.2.5 Calibrating Percent Motor Load ......................................................................................................4.20
Section 4.2.2.6 Setting Speed Parameters.................................................................................................................4.20
Section 4.2.3 Top Stop Calibration Menu Settings .......................................................................................................4.20
Section 4.2.3.1 Top Stop Calibration for Fixed Speed Presses.................................................................................4.22
Section 4.2.3.2 Variable Speed Press Auto Top Stop Calibration ............................................................................4.23
Section 4.2.4 Operator Terminal Configuration ............................................................................................................4.26
Section 4.2.4.1 Top Area (Screen) Display Configuration .......................................................................................4.26
Section 4.2.4.2 Zeroing Stroke Count.......................................................................................................................4.27
Section 4.2.4.3 Key/Code Access Configuration......................................................................................................4.28
Section 4.2.4.4 Auxiliary Communications Setup....................................................................................................4.33
Section 4.2.5 Auxiliary Equipment Messages...............................................................................................................4.33
Section 5 Using the OmniLink II Press Automation Control Standard
Functions and Optional Speed Adjust Function .......................................5.1
Section 5.1 Main Menu (Screen) .........................................................................................................................................5.1
Section 5.2 Brake Monitor and Diagnostic Screen ..............................................................................................................5.2
Section 5.2.1 Brake Monitor ...........................................................................................................................................5.3
Section 5.2.2 Clutch Engagement Time Monitor ............................................................................................................5.4
Section 5.2.3 Critical Angle and Intellistop ....................................................................................................................5.4
Section 5.2.4 Stopping Degrees.......................................................................................................................................5.6
Section 5.2.5 Auxiliary Equipment Messages.................................................................................................................5.7
Section 5.2.6 Reason for the Last Stop............................................................................................................................5.7
Section 5.2.7 Present Running Status..............................................................................................................................5.7
Section 5.2.8 Diagnostics ................................................................................................................................................5.7
Section 5.2.9 Module Limit Switch.................................................................................................................................5.8
Section 5.3 Counters ............................................................................................................................................................5.9
Section 5.3.1 Production Counters ..................................................................................................................................5.9
Section 5.3.1.1 Production Counters On/OFF ..........................................................................................................5.10
Section 5.3.1.2 Production Counters Change Limit .................................................................................................5.11
Section 5.3.1.3 Production Counters Reset...............................................................................................................5.11
Section 5.3.1.4 Production Counters Increment/Decrement.....................................................................................5.11
Section 5.3.1.5 Production Counters Change Count.................................................................................................5.12
Section 5.3.2 Stroke Counter.........................................................................................................................................5.12
Section 5.3.3 Scrap Counter ..........................................................................................................................................5.12
Section 5.3.4 Configure Counters .................................................................................................................................5.13
Section 5.3.4.1 Configure Auxiliary Counter Names ...............................................................................................5.13
Section 5.3.4.2 Configure Counter Count By Value ................................................................................................5.14
Section 5.3.4.3 Configure Counter Every How Many Stroke Value ........................................................................5.14
Section 5.3.4.4 Configure Counter Reset When Order Counter Reset .....................................................................5.15
Section 5.3.4.5 Configure Counter Enable ...............................................................................................................5.15
Section 5.3.4.6 Configure Reset Counters When Job Recalled ................................................................................5.15
Section 5.4 Motor Speed Adjustment (Option)..................................................................................................................5.15
Section 5.5 Quick Access (ACC key) ................................................................................................................................5.16
Section 5.5.1 Machine Notes.........................................................................................................................................5.17
Section 5.5.2 Job Notes .................................................................................................................................................5.17
Section 5.5.3 Editing Machine Notes and Job Notes.....................................................................................................5.17
Section 5.5.4 Auxiliary Communications......................................................................................................................5.18
Section 5.5.5 LOGOUT Softkey ...................................................................................................................................5.18
Section 5.6 Job Setups (Storage and Recall)......................................................................................................................5.18
Section 5.6.1 Store Setup ..............................................................................................................................................5.19