Roland 6-Channel HD Video Switcher with Audio Mixer & PTZ Camera Control (1 RU) - Manual (Page 5)

5
USING THE UNIT SAFELY
WARNING
Turn off the unit if an abnormality or malfunction
occurs
Immediately turn the unit off,
remove the AC adaptor from the
outlet, and request servicing by
your retailer, the nearest Roland
Service Center, or an authorized
Roland distributor, as listed on the
“Information” when:
• The AC adaptor or the power cord has
been damaged; or
• If smoke or unusual odor occurs; or
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or
otherwise has become wet); or
• The unit does not appear to operate
normally or exhibits a marked change in
performance.
Do not share an outlet with an unreasonable
number of other devices
Otherwise, you risk overheating
or fire.
Do not use overseas
Before using the unit in overseas,
consult with your retailer, the
nearest Roland Service Center, or
an authorized Roland distributor, as
listed on the “Information.”
Important Notes on Rack Mounting
When mounting the unit in a rack,
to ensure efficient cooling, give
attention to the following points.
• Install in a well-ventilated
location.
• Never obstruct the exhaust ports on the
unit’s side panels.
• Avoid mounting the unit in a sealed-type
rack. Warm air within the rack cannot
escape and is sucked into the unit, making
efficient cooling impossible.
• If the back of the rack cannot be opened,
install an exhaust port or ventilation fan
at the top back surface of the rack, where
warm air collects.
• When using the unit while mounted in a
movable case (portable rack), remove the
front and rear rack covers so that the front
and back of the unit are not obstructed.
When installing the unit in a rack or the
like, use the mounting screws occupying
the screw holes in the rack-mount brackets
(included with the unit). Also, use due
caution to ensure that your fingers don’t get
pinched.
* Also read the “Placement” section (p. 6)
under “IMPORTANT NOTES.”
CAUTION
When disconnecting the power cord, grasp it by the
plug
To prevent conductor damage,
always grasp the power cord by its
plug when disconnecting it.
Periodically clean the power plug
An accumulation of dust or foreign
objects between the power plug
and the power outlet can lead to
fire or electric shock.
At regular intervals, be sure to pull out the
power plug, and using a dry cloth, wipe away
any dust or foreign objects that may have
accumulated.
Disconnect the power plug whenever the unit will
not be used for an extended period of time
Fire may result in the unlikely event
that a breakdown occurs.
Route all power cords and cables in such a way as
to prevent them from getting entangled
Injury could result if someone were
to trip on a cable and cause the
unit to fall or topple.
Avoid climbing on top of the unit, or placing heavy
objects on it
Otherwise, you risk injury as the
result of the unit toppling over or
dropping down.
Never connect/disconnect a power plug if your
hands are wet
Otherwise, you could receive an
electric shock.
Disconnect all cords/cables before moving the unit
Before moving the unit, disconnect
the power plug from the outlet,
and pull out all cords from external
devices.
Before cleaning the unit, disconnect the power
plug from the outlet
If the power plug is not removed
from the outlet, you risk receiving
an electric shock.
Whenever there is a threat of lightning, disconnect
the power plug from the outlet
If the power plug is not removed
from the outlet, you risk causing
malfunction or receiving an electric
shock.
Keep small items out of the reach of children
To prevent accidental ingestion
of the parts listed below, always
keep them out of the reach of small
children.
• Included Parts
• Rubber feet (p. 3)
CAUTION
Handle the ground terminal carefully
If you remove the screw from the
ground terminal, be sure to replace
it; don’t leave it lying around where
it could accidentally be swallowed
by small children. When refastening the
screw, make that it is firmly fastened, so it
won’t come loose.