Document Outline

• Regulatory Information
  • Cautionary Symbols
  • Warranty Information
• About This Guide
  • Using This Guide
• 1 Introduction and Overview
  • Product Description
    • How the Scanner Works
  • Features and Benefits
  • Before You Begin
  • Equipment Overview
    • Front View
    • Rear View
  • Recommended Configuration of the Host Computer
    • Minimum Host Computer Hardware Requirements
    • Minimum Software Requirements
  • Film Sizes
    • Film Holders Provided with the Scanner
• 2 Connecting and Operating the Scanner
  • Preparing the Host Computer
  • Connecting the Scanner
    • Changing the AC Input Voltage Setting and the Fuses
    • Attaching the Cables
  • Starting Up the Scanner System
    • Placing the Empty Film Holder in the Film Holder Guide
    • Powering up the Scanner and the Host Computer
  • Operating the Scanner
    • Setting the Magnification and Calibrating the Scanner
    • Setting the Scan Parameters
    • Selecting the Negative or Positive Balancing Filter
    • Inserting a Negative or Mounted Slide in the Scanner
      • Preparing a Carded Negative
      • Preparing an Uncarded Negative
      • Preparing a Mounted Slide
      • Placing the Film Holder in the Scanner
    • Focusing
    • Scanning a Single Frame
  • Shutting Down the Scanner
• 3 Validating the Scanner
  • Starting the SAM Software
  • Setting the Magnification
  • Calibrating the Scanner
  • Making a Test Scan
  • Autofocusing
  • Scanning the Image
  • Checking the Scan
• 4 Maintaining the Equipment
  • Cleaning Procedures
    • Cleaning the Lens
    • Cleaning the Light Bar
  • Replacement Procedures
    • Replacing the Lamp
    • Replacing the (Round) Balance Filters
    • Replacing the (Square) IR Filter
• Appendix A: Using the Service and Assembly Module (SAM)
  • Installing the Service and Assembly Module (SAM) Software
    • Backing Up Scanner Files
  • Using the Operations Controls
    • Performing the Functions on the Mag/Focus Tab
      • Setting the Magnification
      • Performing an Autofocus
    • Performing the Functions on the Calibrate/Image Processing Tab
      • From the Operations window, click the Calibrate/Image Processing tab when you need to calibrate t...
      • Setting Image Processing Parameters
      • Calibrating the Scanner
    • Using the Capture Tab
      • Scanning the Image Data
    • Using the Miscellaneous Tab
    • Backing Up and Restoring Files
• Appendix B: Ordering Accessories and Supplies
  • Accessories
  • Supplies
• Appendix C: Scanner Specifications
• Appendix D: Using the Long Roll Accessory
  • Installing the Software for the Long Roll Accessory
    • Downloading the Software and Firmware from KODAK.COM
    • Upgrading the Scanner’s Firmware
  • Installing or Removing the Long Roll Accessory
    • Overview of Parts
    • Preparing the Scanner for the Long Roll Accessory
    • Attaching the Long Roll Accessory to the Scanner
    • Latching and Unlatching the Gate Actuator
      • Latching the Gate Actuator
      • Unlatching the Gate Actuator
    • Installing the Aperture Plate
    • Removing the Long Roll Accessory from the Scanner
  • Punch Sensors
  • Setting the Punch Reader Height for the Current Film Size
    • Adjusting the Core Locator Height on the Spindle
    • Loading and Threading Film
      • Threading the Film
    • Setting the Punch Reader Height
      • Installing the Adjustment Tool
      • Visually Checking the Punch Reader Height
      • Adjusting the Punch Reader Height
    • Preparing and Loading the Film
    • Setting the Lens Magnification
    • Setting the Scan Parameters
    • Locating the First Punched Frame
    • Checking the Alignment and Adjusting the Sensor Offsets
    • Recording the Highest Numbers on the LEDs
    • Determining the Left Trigger Point
    • Determining the Right Trigger Point
    • Setting the Trigger Points at the Scanner
    • Cleaning the Punch Readers
    • Cleaning the Rollers
    • Resetting the Sensors to the Factory Values
    • Programming the Sensors for the Long Roll Accessory
      • Programming the Left Sensor
      • Programming the Right Sensor
        • Numerics
        • A
        • B
        • C
        • D
        • E
        • F
        • H
        • I
        • K
        • L
        • M
        • N
        • O
        • P
        • R
        • S
        • T
        • U
        • V
        • W