Integra DTR-9.1 - Manual (Page 40)

40
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
2.Input Setup
Input:PHONO
1.Digital Setup
2.Multichannel Setup
3.Video Setup
4.Listening Mode Preset
5.Sound Effect
6.Character Input
7.Miscellaneous Setup
Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
2-6.Sound Effect
Input:PHONO
a.Bass : 0
b.Treble : 0
Quit:|OSD|
Input Setup
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
2.Input Setup
Input:TAPE1
1.Digital Setup
2.Multichannel Setup
3.Video Setup
4.Listening Mode Preset
5.Sound Effect
6.Character Input
7.Miscellaneous Setup
Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
2-5.Delay
Input:TAPE1
a.A/V Sync : 0.0ms
Relative Delay
b.Center : 0.0ms
c.Surr L/R : 0.0ms
d.Surr Back : 0.0ms
Quit:|OSD|
2-5. Delay sub-menu
This sub-menu gives you various ways to adjust the
timing of the audio output from the speakers to give
certain soundfield effects or to adjust for unwanted
asynchronous video and audio tracks.
This sub-menu does not appear if “Direct” is selected as
the listening mode.
a. A/V Sync
If a digital signal processor is connected, there may be
times when the audio and video from a DVD or LD
player is not output in perfect sync. The result is where
the sound and picture do not match and the sound is
heard too early. In such a case, use this setting to prop-
erly synchronize the audio and video. This setting can
be set between 0 to 30 ms in 0.5-ms increments. Under
normal circumstances, this can left at 0 ms. For input
sources using the multi channel port, this setting will not
appear.
b. Relative Delay
Besides level and delay adjustments, the DTR-9.1
provides the ability to change or adjust the relative
speaker position to fine tune the soundfield for the
listener. This is accomplished using Integra’s unique
Enhanced Spatial Positioning Algorithm. This
adjustment provides 10 milliseconds of delay for the
speakers, which is equivalent to moving the speaker 10
feet away. This adjustment is set up to provide -4 or +6
milliseconds (-4 or +6 feet) of adjustment to the
listener’s position.
Once the coarse adjustments-speaker level and dis-
tance adjustments-are made, the system is set up to
provide a typical or broad surround environment. By
adjusting the relative position of the speakers, we are
able to alter the soundfield to be more spread out
(deeper) or focused (shallower).
2-6. Sound Effect sub-menu
This sub-menu allows you to increase or decrease only
the low (bass) or high (treble) frequency sounds or
adjust the volume for a particular input source. This sub-
menu does not appear if “Direct” or “THX Mode” are
selected as the listening mode.
a. Bass
Press the cursor button to decrease the bass sounds
and press the cursor button to increase the bass
sounds. The bass can be adjusted between -12 and +12
decibels in two steps.
b. Treble
Press the cursor button to decrease the treble sounds
and press the cursor button to increase the treble
sounds. The treble can be adjusted between -12 and
+12 decibels in two steps.