Integra DTR-9.1 - Manual (Page 86)

Upgraded-
10
Currently
selected
listening mode
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3.Listening Mode Setup
1.Mono(Analog/PCM)
2.Mono(Digital)
3.Stereo(Analog/PCM)
4.Stereo(Digital)
5.Surround(Analog/PCM)
6.Surround(Digital)
7.Theater-Dimensional
Quit:|OSD|
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3.Listening Mode Setup
1.Mono(Analog/PCM)
2.Mono(Digital)
3.Stereo(Analog/PCM)
4.Stereo(Digital)
5.Surround(Analog/PCM)
6.Surround(Digital)
7.Theater-Dimensional
Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3-1.Mono(Analog/PCM)
a.Subwoofer :On
b.Re-EQ/Academy
:Re-EQ
c.Input Channel
:AutoL+R
d.Output Channel
:L+R
Quit:|OSD|
Listening Mode Setup
3-1. Mono (Analog/PCM) Setup
Select this to modify the Mono listening mode when the
current source is analog or PCM. The parameters that
can be set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Input Channel Auto L+R, Left, Right Auto L+R
d Output Channel L+R, Center L+R
3-2. Mono (Digital) Setup
Select this to modify the Mono listening mode when the
current source is digital. The parameters that can be set
are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Input Channel Auto L+R, Left, Right Auto L+R
d Output Channel L+R, Center L+R
3-3. Stereo (Analog/PCM) Setup
Select this to modify the Stereo listening mode when the
current source is analog or PCM. The parameters that
can be set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Upsampling Off, On Off
3-4. Stereo (Digital) Setup
Select this to modify the Stereo listening mode when the
current source is digital. The parameters that can be set
are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
3-5. Surround (Analog/PCM) Setup
Select this to modify the Pro Logic
or DTS Neo:6 mode
when the current source is analog or PCM. The
parameters that can be set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ On, Off Off
c Surround Speakers Surround L/R, Surround Back, Surround L/R
Surround L/R+Back
d Upsampling* Off, On Off
e Surround Mode PL Movie, PL Music PL Movie
DTS Neo:6 Cinema,
DTS Neo:6 Music
f PL Music Off, On Off
Panorama
g PL Music 0, 1, 2, 3, 4, 5 3
Dimension
h PL Music 0, 1, 2, 3, 4, 5 3
Center Width
i Neo:6 Music 0, 1, 2, 3, 4, 5 3
Center Image
* When Upsampling is set to “On,” DTS Neo:6 cannot be
selected.
3. Listening Mode Setup menu
This menu allows you to make fine adjustments to the
listening modes you have set for each input source
with the Listening Mode Preset sub-menu. These
adjustments are in the form of parameters and each
one is explained below. Note that some parameters
cannot be set for some listening modes and that no
sub-menu will have all parameters. Also, for some
input signal formats, changes in the listening mode
parameters may actually result in no change to the
resulting output signal.