Integra DTR-9.1 - Manual (Page 92)

SN 29343353 D0203-1
ONKYO CORPORATION
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 E-mail: [email protected]
ONKYO EUROPE ELECTRONICS GmbH
Industriestrasse 20, 82110 Germering, GERMANY
Tel: 089-849-320 Fax: 089-849-3265 E-mail: [email protected]
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
Printed in Japan E
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
2.Input Setup
Input:TAPE1
1.Digital Setup
2.Multichannel Setup
3.Video Setup
4.Listening Mode Preset
5.Sound Effect
6.Character Input
7.Miscellaneous Setup
Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
2-5.Delay
Input:TAPE1
a.A/V Sync : 0.0ms
Relative Delay
b.Center : 0.0ms
c.Surr L/R : 0.0ms
d.Surr Back : 0.0ms
Quit:|OSD|
Other upgraded function
Selecting audio input signal using the AUDIO
button on the remote controller (new function)
AUDIO MUTING
DISC TRACK
AUDIO
button
Input Setup
2-5. Delay sub-menu
This sub-menu gives you various ways to adjust the timing
of the audio output from the speakers to give certain
soundfield effects or to adjust for unwanted asynchronous
video and audio tracks.
This sub-menu does not appear if “Direct” is selected as
the listening mode.
a. A/V Sync
If the video signal is progressive-processed using projector
or other devices, the sound and picture may not match
and the sound is heard too early. In such a case, use this
setting to properly synchronize the audio and video. This
setting can be set between 0 and 120 ms in 0.5-ms
increments. Under normal circumstances, this can left at
0 ms. For input sources using the multi channel port, this
setting will not appear.
Note:
When you use the listening mode of DTS 96/24, A/V Sync
and Relative Delay will not be activated.
Press the AUDIO button on the remote controller to
change the audio mode. Each time the button is
pressed, the mode changes from “AUTO”
→
“Multichannel” → “Analog” and back to “AUTO.” The
“AUTO” audio mode is recommended for normal
circumstances.
AUTO (automatic detection): With this setting, this unit
automatically detects whether the input signal is digital or
analog. When a digital signal is not input, then the analog
signal is played. This setting is effective when the input
source is assigned to Digital Input in Audio Setup.
Multichannel: Select this setting to play back the input
from the component connected to the MULTI CHANNEL
INPUT port. This setting is effective when the Multichannel
setting in “2-2. Multichannel Setup” is set to “Yes.”
Analog: Select this setting to play back the input from a
source component connected to an analog audio input
jacks. With this setting, even if a digital signal is input from
the same component, only the analog signal will be
output.