JAI AD-081GE - Manual (Page 66)

AD-081GE
65
12.2. Specifications Table
Specifications AD-081GE
Scanning system Progressive scan
Frame Rate Full scan 30.0 frames / sec. Progressive (768 lines/frame)
Pixel clock 33.75MHz
Line frequency 23.768 KHz (1420 pixel clocks / line)
Image sensor 1/3 inch Monochrome IR IT CCD
Sensing area 4.76 (H) x 3.57 (V) mm
Cell size 4.65 (H) x 4.65 (V) µm
Active pixels 1024(H) x 768 (V)
Pixels in Video output Full
Variable Partial
Vertical binning
1024 (h) x 768 (v) 30.0 fps. H = 23.768 kHz
Scan height 1 to 760 lines,
Start line 8 to 768
1024(h) x 384(v), 49.30 fps (max.) H=19.62 KHz
Sensitivity on sensor 0.34 lux (Max. Gain, Shutter OFF, 50% Video Level)
S/N ( dB) More than 54 dB (0dB)
Iris video output, Analogue 0.7 V p-p (without Sync)
Digital Video Output Via RJ-45 x 2 (GigE1 and GigE2)
Mono8, Mono10, Mono10_Packed, Mono12_Packed, Mono12
Input signals
(TTL/75Ω) x2, LVDS x 1 HIROSE 6-pin
OPT x2 HIROSE 12-pin
Output signals
TTL x 1 Hirose 6-pin
OPT x 2 Hirose 12-pin
Gain
Manual Gain: -3dB to +21dB (o.35dB step)
AGC: -3dB to +21dB
Knee compensation Knee point and knee slope
LUT/Gamma 1.0/0.6/0.45/LUT
Shading compensation ON/OFF
Synchronization Int. X-tal
GPIO Module
Input /Output switch
Clock Generator(one)
Pulse generator (Four)
Configurable 21-in / 14-out switch
12 bit counter based on pixel clock
20-bit counter programmable for length, stat point, stop point , repeat
Hardware Trigger mode Edge Pre-select, Pulse width control, RCT, PIV, Frame delay, Sequence
OB area transfer mode ON / OFF
Event message Exposure start, Exposure end, Trigger IN, Video start, Video end
Electronic Shutter
Programmable Exposure
Exposure Time Abs
GPIO plus Pulse width
Auto shutter
20 µs to 792L(33.3ms) in 1L step
µsec – user definable. Same range as PE
Max. 2 sec (fine setting with GPIO and pulse width control)
1/30 to 1/10000 sec
Accumulation LVAL synchronous or LVAL asynchronous automatic selection
Interface Gigabit Ethernet (IEEE802.3, ATA GigE Vision Standard) 2 lines
Functions controlled via GigE
Vision Interface Shutter, Gain, Black Level, Trigger mode, Readout mode,
GPIO setup, ROI (GenICam mandatory functions )
GigE Vision Streaming Control
Packet size, Delayed (Frame) readout, inter-packet delay
Jumbo frame can be set at max. 16K (16020), Default packet size is 1476 Byte.
Indicators on rear panel Power, Hardware trigger, GigE Link, GigE activity
Lens Mount C-Mount (Rear protrusion less than 4mm). Designed For 3CCD camera
Flange back 17.526mm Tolerance 0 to – 0.05mm
Operating temperature -5  C to +45  C
Operating humidity 20 to 80% (non-condensing)