Sony HDW-1800 - Manual (Page 75)

75
9-2 Setup Menu Operations
Chapt
er 9 Set
u
p
Men
u
s
1
Select F6 (SELECT).
The cursor moves to the setting value of the selected
sub-item.
2
Select F3 (–) or F4 (+), or turn the MULTI CONTROL
knob to select a desired setting value.
To select another sub-item and change its setting
value
Select F5 (RETURN) to move the cursor to a sub-item
name and repeat the procedure for selecting a desired
sub-item and changing its setting value.
To select another menu item and change its setting
value
Select F5 (RETURN) twice in succession to display
the menu item list, and repeat the procedure for
selecting a desired menu item and changing its setting
value.
3
When all required changes have been made, select F9
(SET).
The new settings are confirmed.
To cancel changes and exit from the setup menu
Select F10 (EXIT).
When F9 (SET) is not selected, all changes are
cancelled.
To reset the menu settings to their factory
default values (menu item B20)
Use the following procedure.
1
Carry out steps 1 to 3 of the procedure described in the
section “To change the settings of menu items without
sub-items” on page 74 to set menu item B20 “RESET
SETUP” to “ON”.
The message “Push SET button!” appears.
2
Select F9 (SET).
3
Select F9 (SET) again.
The menu settings are saved .
To recall the BANK4 settings (menu item
B20)
To set the current menu settings to the BANK4 settings,
carry out the following operation.
1
Carry out steps 1 to 3 of the procedure described in
“To change the settings of menu items without sub-
items” (page 74), then set menu item B20 “RESET
SETUP” to “bank-4”.
The message “Push SET button!” appears.
2
Select F9 (SET).
The display returns to the menu item list.
The current menu settings are set to the settings in
BANK4.
3
Select F9 (SET) again.
The settings are saved, exiting from the setup menu.
To switch the system frequency (menu
item 013)
To switch the system frequency among 59.94i, 50i,
29.97PsF, 25PsF, 24PsF and 23.98PsF, proceed as
follows.
• Before carrying out this operation, consult the person
responsible for system installation.
• When this unit enters 24PsF or 23.98PsF mode, SDI
(D1) and composite signals are not output.
1
Carry out steps 1 to 3 of the procedure described in
“To change the settings of menu items without sub-
items” (page 74) to set menu item 013 “SYSTEM
FREQUENCY SELECT” to “ON”.
The menu display changes to allow switching of the
system frequency among 59.94i, 50i, 29.97PsF,
25PsF, 24PsF and 23.98PsF.
2
Switch the setting, then select F9 (SET).
3
Turn the unit off.
Next time the unit is powered on, it will operate in the
selected mode.
Menu bank operations (menu items B01 to
B13)
This unit saves menu settings in what are termed “menu
banks”. Saved sets of menu settings can be recalled for use
as required.
To save the current active menu settings
Set one of menu items B11 “SAVE BANK 1” to B13
“SAVE BANK 3” to “ON”, depending on the menu banks
you want to save in, then select F9 (SET).
To recall settings from a menu bank
When recalling the settings saved in one of menu banks 1
to 3, set one of the corresponding menu items B01
“RECALL BANK 1” to B03 “RECALL BANK 3” to
“ON”, then select F9 (SET).
Notes