KORG TRITON STUDIO music workstation - Manual (Page 49)

PROG
1.1
2.1
2.2
2.3
3.1
4.1
4.2
5.1
5.2
5.3
6.1
6.2
6.3
6.4
7.1
7.2
7.3
39
Separately from this setting, you can use control change
#92 to turn off all insert effects together. A value of 0
will be off, and a value of 1–127 will be the original set-
ting. This message is received on the global MIDI chan-
nel specified by “MIDI Channel” (GLOBAL 2.1–1a).
Insert Effect 1, 5 [000...089: name]
Insert Effect 2, 3, 4 [000...102: name]
Indicates the type of each insert effect.
For “Insert Effect 1” and “Insert Effect 5” you can select from
90 types of effect: 000: No Effect – 089: Reverb-Gate. Dou-
ble-size effects cannot be used.
For “Insert Effect 2,” “Insert Effect 3” and “Insert Effect 4”
you can select from 103 types of effect: 000: No Effect – 102:
Hold Delay
.
If you select a double-size effect, the next insert effect will be
unavailable for use. For example if you select a double-size
effect for IFX2, IFX3 cannot be used. A maximum of two
double-size effects can be used (normal size for IFX1, double
size for IFX2 and IFX4) (
☞ p.160).
These effects can also be selected by category in Utility
“Select by Category” (7.2–1b).
Chain [ (Off), (On)]
Indicates “chain” on/off for each insert effect.
For example if “Chain” for IFX1 is set to
(On), IFX1 and
IFX2 will be connected in series. If “BUS Select” (7.1–1a) is
set to IFX1, IFX1 and IFX2 will be inserted in series.
A maximum of five insert effects (IFX1–IFX5) can be
inserted in series. When effects are chained, the “Pan
(CC#8),” “BUS Select,” “S1 (Send1(MFX1))” and “S2
(Send2(MFX2))” settings that follow the last IFX in the chain
will be used.
Pan(CC#8) (Post IFX Pan CC#8) [L000...C064...R127]
Sets the pan after the sound has passed through the insert
effect. This setting is valid only when the following “BUS
Select” is set to L/R (
☞ p.162).
CC#8 will control.
BUS Select [L/R, 1, 2, 1/2, Off]
Specifies the bus to which the sound will be sent after pass-
ing through the insert effect. Normally you will set this to L/
R
. If you wish to output to AUDIO OUTPUT (INDIVID-
UAL), set this to 1, 2 or 1/2. The Off setting is used when
you wish to use “S1 (Send1(MFX1))” and “S2
(Send2(MFX2))” and in addition connect to the master
effects in series.
S1 (Send1 (MFX1)) [000...127]
S2 (Send2 (MFX2)) [000...127]
Sets the send levels to the master effects 1 and 2 for the
sound that has passed through the insert effect. These set-
tings are valid when “BUS Select” (7.1–1a) has been set to L/
R
or Off.
Control change CC#93 will control the Send 1 level, and
control change CC#91 will control the Send 2 level.
These messages are received on the global MIDI chan-
nel specified by “MIDI Channel” (GLOBAL 2.1–1a).
■ 7.2–1b: UTILITY
☞ “Write Program” (1.1–1c), “Copy Insert Effect,” “Swap
Insert Effect” (7.1–1c)
Select by Category
Indicates insert effects by category.
For the procedure, refer to “Select by Category” (
☞ p.2).
This command can be used when selecting “Insert
Effect 1”–”Insert Effect 5.”
7.2–2: IFX 1
(Insert Effect1)
7.2–3: IFX 2
(Insert Effect2)
7.2–4: IFX 3
(Insert Effect3)
7.2–5: IFX 4
(Insert Effect4)
7.2–6: IFX 5
(Insert Effect5)
Here you can set the effect parameters for the IFX 1/2/3/4/
5 that were selected in the Setup page (
☞ p.168).
Effect dynamic modulation (Dmod) is controlled on the
global MIDI channel “MIDI Channel” (GLOBAL 2.1–
1a). (
☞ p.227 “Dynamic Modulation Source (D.mod)”)
7.2–2a