Document Outline

• Revision
• Copyright
• Table of Contents
• List of Figures
• List of Tables
• 1 Introduction
  • 1.1 Overview
  • 1.2 Model Variations
  • 1.3 Features
  • 1.4 Technical Specifications
  • 1.5 Front Panel
  • 1.6 Rear Panel
  • 1.7 Dimensions
• 2 Unpacking
  • 2.1 Anti-static Precautions
  • 2.2 Unpacking Precautions
  • 2.3 Packing List
• 3 Installation
  • 3.1 Installation Precautions
  • 3.2 Installation and Configuration Steps
  • 3.3 Wi-Fi Antenna Installation (Wi-Fi Model Only)
  • 3.4 AT/ATX Mode Selection
    • 3.4.1 AT Power Mode
    • 3.4.2 ATX Power Mode
  • 3.5 Reset the System
  • 3.6 Powering On the System
  • 3.7 Mount the System
    • 3.7.1 Wall Mount
    • 3.7.2 VESA mount 75
    • 3.7.3 VESA mount 100
  • 3.8 External Peripheral Interface Connectors
    • 3.8.1 Audio Connection
    • 3.8.2 HDMI Device Connection
    • 3.8.3 LAN Connection
    • 3.8.4 RS-232Serial Port Connection
    • 3.8.5 RS-422/485 Serial Port Connection
    • 3.8.6 USB Device Connection
    • 3.8.7 VGA Monitor Connection
• 4 System Motherboard
  • 4.1 Overview
    • 4.1.1 Layout
  • 4.2 Internal Peripheral Connectors
    • 4.2.1 Battery Connector (BAT1)
    • 4.2.2 BIOS Programming Connector (SPI1)
    • 4.2.3 Debug port Connector (DEBUGCN1)
    • 4.2.4 HDD LED Connector (HDDLED1)
    • 4.2.5 JSATA Connector (JSATA2)
    • 4.2.6 Power LED Connector (PWRLED1)
    • 4.2.7 USB 2.0 Connector (USB4_5)
    • 4.2.8 SATA Connector (S_ATA1)
    • 4.2.9 SATA Power Connector (CN1)
  • 4.3 External Interface Panel Connectors
    • 4.3.1 Audio Jack (JAUDIO1)
    • 4.3.2 Ethernet Connector (LAN1)
    • 4.3.3 HDMI Connector (HDMI1)
    • 4.3.4 Power Connector (DC_JACK1)
    • 4.3.5 RS-232 Serial Ports (COM1, COM2)
    • 4.3.6 RS-422/485 Serial Port (COM3)
    • 4.3.7 USB 2.0 Connectors (USB0_1)
    • 4.3.8 USB 2.0 Connector (USB23)
    • 4.3.9 VGA Connector (VGA1)
  • 4.4 Jumper Settings
    • 4.4.1 AT/ATX Mode Select Jumper (J_AUTOPWR1)
• 5 System Maintenance
  • 5.1 System Maintenance Introduction
  • 5.2 Anti-static Precautions
  • 5.3 Turn off the Power
  • 5.4 Replacing Components
    • 5.4.1 Hard Disk Drive (HDD) Replacement
    • 5.4.2 Memory Module Replacement
    • 5.4.3 WLAN Card Replacement
• 6 BIOS
  • 6.1 Introduction
    • 6.1.1 Starting Setup
    • 6.1.2 Using Setup
    • 6.1.3 Getting Help
    • 6.1.4 Unable to Reboot after Configuration Changes
    • 6.1.5 BIOS Menu Bar
  • 6.2 Main
  • 6.3 Advanced
    • 6.3.1 ACPI Configuration
    • 6.3.2 RTC Wake Settings
    • 6.3.3 CPU Configuration
    • 6.3.4 SATA Configuration
    • 6.3.5 USB Configuration
    • 6.3.6 F81866 Super IO Configuration
      • 6.3.6.1 Serial Port n Configuration
        • 6.3.6.1.1 Serial Port 1 Configuration
        • 6.3.6.1.2 Serial Port 2 Configuration
        • 6.3.6.1.3 Serial Port 3 Configuration
    • 6.3.7 F81866 H/W Monitor
    • 6.3.8 Serial Port Console Redirection
      • 6.3.8.1 Console Redirection Settings
  • 6.4 iEi Feature
  • 6.5 Chipset
    • 6.5.1 Host Bridge Configuration
      • 6.5.1.1 Intel IGD Configuration
    • 6.5.2 Southbridge Configuration
  • 6.6 Boot
  • 6.7 Security
    • 6.7.1 HDD Security Configuration
  • 6.8 Save & Exit
• 7 Software Drivers
  • 7.1 Available Software Drivers
  • 7.2 Starting the Driver Program
  • 7.3 Chipset Driver Installation
  • 7.4 Graphic Driver Installation
  • 7.5 LAN Driver Installation
  • 7.6 Audio Driver Installation
• A Safety Precautions
  • A.1 Safety Precautions
    • A.1.1 General Safety Precautions
    • A.1.2 Anti-static Precautions
    • A.1.3 Product Disposal
  • A.2 Maintenance and Cleaning Precautions
    • A.2.1 Maintenance and Cleaning
    • A.2.2 Cleaning Tools
• B BIOS Menu Options
• C One Key Recovery
  • C.1 One Key Recovery Introduction
    • C.1.1 System Requirement
    • C.1.2 Supported Operating System
  • C.2 Setup Procedure for Windows
    • C.2.1 Hardware and BIOS Setup
    • C.2.2 Create Partitions
    • C.2.3 Install Operating System, Drivers and Applications
    • C.2.4 Building the Recovery Partition
    • C.2.5 Create Factory Default Image
  • C.3 Auto Recovery Setup Procedure
  • C.4 Setup Procedure for Linux
  • C.5 Recovery Tool Functions
    • C.5.1 Factory Restore
    • C.5.2 Backup System
    • C.5.3 Restore Your Last Backup
    • C.5.4 Manual
  • C.6 Restore Systems from a Linux Server through LAN
    • C.6.1 Configure DHCP Server Settings
    • C.6.2 Configure TFTP Settings
    • C.6.3 Configure One Key Recovery Server Settings
    • C.6.4 Start the DHCP, TFTP and HTTP
    • C.6.5 Create Shared Directory
    • C.6.6 Setup a Client System for Auto Recovery
  • C.7 Other Information
    • C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller
    • C.7.2 System Memory Requirement
• D Watchdog Timer
• E Hazardous Materials Disclosure
  • E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury