Alpine IVA-D300 - Manual (Page 34)

32
-EN
SYSTEM Setup
System Setup Operation
To display the System mode screen:
To watch a video source, your vehicle must be parked with
the ignition key in the ACC or ON position. To do this, follow
the procedure below.
1. Brake to bring your vehicle to a complete stop at a
safe location. Engage the parking brake.
2. Keep pushing the foot brake and release the parking
brake once then engage it again.
3. When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission
lever in the Park position.
Now, the locking system for the System mode operation has
been released. Engaging the parking brake can reactivate
the System mode, as long as the car's ignition has not been
turned off. It is not necessary to repeat the above
procedure (1 through 3), of “To display the System mode
screen.”
Each time the ignition is turned OFF, perform the procedure
of “To display the System mode screen.”
The following steps 1 to 5 are common operations to each
“Setting item” of SYSTEM Setup. Refer to each section for
details.
1
Touch [SYS.] on the main source screen.
The SYSTEM selection screen is displayed.
2
Touch [SETUP].
The SETUP screen appears.
3
Touch [ ] of SYSTEM SETUP.
The SYSTEM setup screen appears.
4
Touch [;] or [:] of the desired item to change its
setting.
Setting items:
IN INT. MUTE / IN INT. ICON / NAV. IN / NAV. MIX /
EXPANSION BOX*
1 / VISUALIZER* 2 / AUX IN-1 / AUX IN-2* 2 /
AUX IN-3* 2 / MONITOR OUT-1 / MONITOR OUT-2* 2 / CAMERA
IN / V.SEL KEY / A. PROC TYPE
* 1 The setting is effective when the external expansion Box (VPE-
S431) is connected.
* 2 Displayed when the expansion Box is set to ON.
5
Touch [RETURN] to return to the previous screen.
Touch [MAIN CONT.] to return to the main source screen
that was displayed before the setup operation was
started.
• Immediately after inputting titles or changing the settings of
System Mode (While the system is inputting the titles or data
automatically) do not turn the ignition key (engine key) to OFF.
Otherwise, a title may not be written, or the settings may not be
changed.
Setting the External Device Interrupt Mode
If an Alpine Ai-NET Auxiliary Input Adapter (KCA-801B) is
connected to the IVA-D300, an Auxiliary Source will be allowed to
interrupt the current audio source. For example, you can listen to a
portable MP3 player through your car audio system even with a CD
changer connected and playing. The CD changer will automatically
mute when switched to the AUX Input. For further details on how to
use the Alpine KCA-801B, see your authorized Alpine dealer.
Setting item: IN INT. MUTE
Setting content: OFF / ON
OFF: The volume level can be adjusted in Interrupt mode.
ON:
Sound will not be output. The icon that is set in “Setting
the Interrupt Icon Display” is displayed.
• The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it
manually.
Setting the Interrupt Icon Display
The unit can display the icon of an external device, such as a
telephone, whenever a phone call comes in to tell you there is a phone
call.
Setting item: IN INT. ICON
Setting content: INT / TEL
INT: The INT icon appears on the display.
TEL: When the external device (telephone) sends the
interrupt signal, the telephone icon appears on the
display.
• TEL icon on this setting is not related to TEL Link Operation
(pages 55-57).
Setting the Navigation Mode
When you connect an optional navigation equipment, set it to ON.
Setting item: NAV. IN
Setting contents: OFF / ON
ON: Navigation source is displayed.
OFF: Navigation source is not displayed. The settings related
to the navigation can not be changed from this unit.
Setting the Navigation Interruption
With an Alpine navigation system connected to the IVA-D300, the
voice guidance of the navigation system will be mixed with the radio
or CD play.
Setting item: NAV.MIX
Setting content: OFF / ON
OFF: The navigation interruption mode is turned off.
ON:
The navigation interruption mode is on.
To adjust the navigation interruption volume level, the
adjustment for NAV. LEVEL can be performed in “Adjusting the
Audio” on page 22 after setting to ON.
• The audio volume during the navigation guide can be set by
adjusting the audio volume while the navigation guide continues.
When the navigation guide finishes, the previous audio volume and
the previous screen are restored. For exception, if the navigation
cuts in when the audio volume is lower than the setting level, the
audio volume during the navigation guide is reset the current
listening volume. (When the navigation guide cuts in, the audio
volume does not increase.)
• This setting is effective when NAV.IN of SYSTEM list screen is ON.
• When PXA-H510 or PXA-H900 is connected, NAV.MIX value set in
this unit does not affect PXA-H510 or PXA-H900.