Alpine IVA-D300 - Manual (Page 36)

34
-EN
Optical Digital Input Selection for an External Audio
Processor
Make sure “OPTICAL OUT” is ON in “Setting the Digital Output”
(page 30) before switching this setting.
Setting item: A.PROC TYPE
Setting contents: PXA-H510 / OTHER
OTHER:
When connecting any audio processor via an optical
digital cable except the PXA-H510.
Connect the optical digital input connector with the
connector for the Head unit.
PXA-H510:
When connecting PXA-H510.
Connect the optical digital input connector with the
connector for the DVD.
• After input selection is completed, turn ignition OFF and back ON
again. Your setting of the optical digital input switch is completed.
DISPLAY Setup
Display Setup Operation
To display the Display mode screen:
To watch a video source, your vehicle must be parked with
the ignition key in the ACC or ON position. To do this, follow
the procedure below.
1. Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2. Keep pushing the foot brake and release the parking
brake once then engage it again.
3. When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission
lever in the Park position.
Now, the locking system for the Display mode operation has
been released. Engaging the parking brake can reactivate
the Display mode, as long as the car's ignition has not been
turned off. It is not necessary to repeat the above procedure
(1 through 3), of “To display the Display mode screen.”
Each time the ignition is turned OFF, perform the procedure
of “To display the Display mode screen.”
The following steps 1 to 5 are common operations to each
“Setting item” of DISPLAY Setup. Refer to each section for
details.
1
Touch [SYS.] on the main source screen.
The SYSTEM selection screen is displayed.
2
Touch [SETUP].
The SETUP screen appears.
3
Touch [ ] of DISPLAY SETUP.
The DISPLAY setup screen appears.
4
Touch [;] or [:] of the desired item to change its
setting.
Setting items:
DIMMER / DIMMER LOW LEVEL / BACKGROUND / AUTO
BACKGROUND / FONT TYPE / FONT COLOR / TOUCH
PANEL / SCREEN ALIGNMENT
5
Touch [RETURN] to return to the previous screen.
Touch [MAIN CONT.] to return to the main source screen
that was displayed before the setup operation was
started.
• Immediately after inputting titles or changing the settings of
Display Mode (While the system is inputting the titles or data
automatically) do not turn the ignition key (engine key) to OFF.
Otherwise, a title may not be written, or the settings may not be
changed.
Illumination Control
Backlighting is provided by a fluorescent light built into the liquid
crystal panel. The illumination control adjusts the brightness of the
backlighting based on the car ambient lighting for easier viewing.
Setting item: DIMMER
Setting content: OFF / ON / AUTO
OFF: Deactivate Auto Dimmer mode to keep the
background illumination of the monitor bright.
ON: Keep the background illumination of the monitor dark.
AUTO: Adjust the brightness of the background illumination
of the monitor automatically to the brightness of the
car interior.
However, when set to AUTO with the monitor closed,
the button lighting will become active when the
headlights are turned on. (This is not functional if the
illumination lead of the unit is not connected).
Adjusting the Minimum Level of Backlight
You can adjust the brightness of the backlight (LOW). This function
could be used, for instance, to change the screen brightness while
travelling at night.
Setting item: DIMMER LOW LEVEL
Setting content: -15 to +15
You can adjust the level between MIN (-15) and MAX (+15).
When it reaches the minimum or maximum point, the display
shows “MIN” or “MAX” respectively.
Switching Background Textures
You have a choice of 5 different background textures preset at the
factory.
Setting item: BACKGROUND
Setting content: MODE1 to 5
• When you select a source other than the built-in disc on this unit,
and the built-in disc is selected on the rear monitor connected to
the unit, background textures cannot be displayed on the unit.
• When an error message is displayed (ERROR, HI-TEMP, etc.),
background textures selected by this setting cannot be displayed on
the unit.