Alpine IVA-D300 - Manual (Page 44)

42
-EN
Setting AMP Link (Optional)
Adjusting and Storing/Recalling the External
Amplifier (Option)
When an external amplifier (MRD-M301 or MRD-M501) is
connected, you can set it from this unit. Up to eight amplifiers can be
set.
• If amplifier settings are made on the unit, do not then change the
setting with the amplifier buttons, as the amplifier display may not
match the operation of the unit.
1
Touch [SYS.] on the main source screen.
The SYSTEM selection screen appears.
2
Touch [i-Personalize].
The i-Personalize screen appears.
3
Touch [ ] of AMPLIFIER LINK.
The AMPLIFIER LINK list screen* appears.
* Connected external amplifiers are listed, and their temperature
Fahrenheit (°F), voltage, and electric current are displayed.
4
Touch [ ] of the amplifier to be adjusted from the
AMPLIFIER LINK list screen.
The mode list screen for adjustment appears.
5
Touch [;] or [:] of the desired adjustment mode.
Adjustment mode:
INPUT SELECT / INPUT GAIN / INPUT GAIN FACTOR / LP /
LP FREQ. / LP SLOPE / SUBSONIC / SUBSONIC FREQ. /
P-EQ / P-EQ FREQ. / P-EQ Q / P-EQ LEVEL / BASS COMP. /
BASS COMP.MODE / T.CORR / T.CORR DELAY TIME / PHASE
/ TURN ON DELAY TIME / OUTPUT DISABLE / MEMORY
WRITE
/ MEMORY READ / NAME
• For details of the adjustment mode, refer to the Owner’s Manual of
the external amplifier.
6
To adjust another amplifier, touch [RETURN] and
then repeat Steps 4 and 5 above.
7
Touch [RETURN] to return to the previous screen.
Touching [MAIN CONT.] restores the main source screen
that was displayed before amplifier adjustment was
started.
Storing Contents of the Amplifier Adjustment
1 After adjusting the amplifier, select P-1 or P-2 by
touching [ ; ] or [ : ] of MEMORY WRITE from the
adjustment mode list.
2 Touch [WRITE].
The contents of the adjustment will be stored on the
preset number you have touched.
• The stored information remains undeleted even if a reset operation
is performed, or if the battery cord is disconnected.
Data Downloading
1
Insert the CD-R/CD-RW disc containing the data.
• If the optional HDA-5460 is connected, steps 2 to 7 can be
performed after the data has downloaded removable hard disc. The
MM DRIVER main source screen can then be selected on this unit.
• If audio data is contained in a CD-R/CD-RW, set to “MP3” in
“Playing MP3/WMA Data” (page 31).
2
Touch [SYS.].
The SYSTEM selection screen appears.
3
Touch [i-Personalize].
The i-Personalize screen appears.
4
Touch [ ] of DATA DOWNLOAD.
5
Touch [ ] of SOUND SETUP.
The unit starts searching the disc for data. When the data
search has completed, the Data Download file selection
screen is displayed.
• If a file is not found by the data search, “NO FILE” is indicated.
6
Touch [ ] of file which is to be downloaded.
Data downloading starts.
When data has been successfully downloaded, the
confirmation screen is displayed for 5 seconds, and the
screen returns to the file selection screen.
PARAMETRIC EQ data
The data is memorized in Preset 6 of Parametric EQ mode.
The memorized data settings in Preset 6 (Parametric EQ
mode) are automatically applied.
X-OVER (Crossover) data
The data is memorized in Preset 6 of X-OVER mode. The
memorized data settings in Preset 6 (X-OVER mode) are
automatically applied.
TIME CORRECTION data
The data is memorized in Preset 6 of the Time correction
mode. The memorized data settings in Preset 6 (Time
Correction mode) are automatically applied.
7
Touch [RETURN] to return to the previous screen.
Touch [MAIN CONT.] to return to the main source screen
which was previously set.
• When you download the data again, the data is overwritten in
Preset 6.