Document Outline

• Lgpm-im.pdf
  • Table of Contents
    • GENERAL DESCRIPTION 5
      • Block Diagram 5
      • Safety Summary 6
      • Basic Operation 7
      • Messages 8
        • User Input Message Request Operation 8
        • Binary Message Request Operation 8
        • Output Message Request 8
        • Message Cancellation 8
      • Overflow Indication 9
      • Peak & Valley 9
      • Normal Operating Mode 9
      • Keypad Description 10
        • Keypad Functions 10
        • Program Code Number (PRO.CODE) 11
      • Front Panel Accessible Functions With Program Disable 11
    • PROGRAMMING GENERAL DESCRIPTION 12
      • Program Presets & Counter Load Module 13
        • Preset Values 13
        • Counter Load Value 13
      • Program Scale Factors Module 14
        • Count Scale Factor 14
        • Rate Scale Factor 14
    • PROGRAMMING MENUS 15
      • Program Scaling Module 16
        • Count Scale Factor (COUNT SF) 16
        • Rate Scale Factor (RATE SF) 16
        • Count Scale Multiplier (CNT.SCM) 16
        • Rate Scale Multiplier (RATE SCM) 16
        • Rate Conversion Factor (RATE PER) 16
        • Decimal Point (CNT. DP, RATE DP) 17
        • Change Count Value With Scale Factor (CHG CNT W/SF) 17
      • Program Rate Module 18
        • Minimum And Maximum Update Time 18
      • Program Counter Module 19
        • Count Modes (CNT.INPUT) 19
        • Counter Reset Action 20
        • Counter Automatic Reset (AUTO RST) 20
      • Program User Module 21
        • Binary Message Request (BIN MSG REQ) 22
        • No Mode 22
        • Maintained Reset (MNT RST) 22
        • Momentary Reset (MOM RST) 22
        • Reset Output (RST OUT) 22
        • Set Output (SET OUT) 22
        • View/Freeze Display (VIEW DS1) 23
        • Change Display (CHG DSP) 23
        • Request Message (REQ MSG#) 23
        • Clear Message (CLR MSG) 23
        • Skip Preset (SKIP PRS) 23
        • Counter Load (CNT LD) 23
        • Print Request (PRINT RQ) 23
        • Program Disable (PGM.DIS.) 23
        • Inhibit Count 23
      • Program Outputs Module 24
        • Phase 24
        • Output Modes - Timed, Latched, Boundary Or HI/LO Acting 24
        • Rate Output On/Off Delay 24
        • Output End (Reset) Modes - OUT1 END, OUT2 END 26
        • Output Power Up State ([email protected], [email protected] OR [email protected]) 26
        • Reset Output With Count (RST/C-EN OR DS) 26
        • Request Message (REQMSG#—) 26
      • Program Display Module 27
        • Displays 1 To 4 27
        • Scroll Speed (SCRO.SPD) 27
        • Display Intensity (DSP.LEVEL) 27
        • Custom Display Lines (CUST.DSP.1 / CUST.DSP.2) 27
        • Program Mnemonic 27
      • Program Message Module 29
        • Message Type 29
        • Message Text 30
        • ASCII Table Of Extended Characters 31
        • ASCII Table Of Standard Characters 32
        • Message Priority (PRIOR - 1) 33
        • Blinking Message (BLNK-YES/NO) 33
        • Multiplex (MUX - YES/NO) 33
        • Maintained/Momentary Message Request 33
        • Message Cancellation 33
        • Message Time 33
        • Message Color 33
      • Program Communication Port Module 34
        • Baud Rate 34
        • Parity/ Number Of Data Bits 34
        • Unit Address 34
        • Serial Transmit Delay 34
      • Program Print Options Module 35
        • Mnemonics (MNEM-Yes/No) 35
        • Transmit And Reset (TX&R-Yes/No) 35
        • Transmit Message #0 (MSG0-Yes/No) 35
      • Program Options Module 36
        • Operator Access 36
        • Preset Tracking 36
        • Program Code (PRO.CODE) 36
        • User/Factory Settings 37
        • LGPM Factory Settings Chart 37
        • LGPM User Settings Programming Sheet 39
    • SERIAL COMMUNICATIONS 42
      • Programming Software 42
        • Installing Software 42
        • Using Software 42
      • Communication Format 43
      • Sending Commands And Data 43
      • Receiving Data 46
      • Terminal Emulation Program For IBM ® PC 47
      • Serial Connections 48
        • Terminal Descriptions 48
        • Connecting To A Host Terminal 49
        • Troubleshooting Serial Communications 50
      • INSTALLATION & CONNECTIONS 51
        • EMC Compliance Installation 52
        • Additional EMC Installation Guidelines 52
        • Wiring Connections 53
          • User Input Wiring 53
          • A.C. Power Wiring 53
          • DC Power Wiring 53
          • Serial Communications 53
        • Signal Wiring 54
          • Inputs A & B 54
        • DIP Switch Set-Up 55
        • Various Sensor Output Connections 56
    • SPECIFICATIONS & DIMENSIONS 57
    • TROUBLESHOOTING GUIDE 60
    • APPENDIX “A” - SCALING FOR COUNT INDICATION 63
      • Scaling For Count Indication 63
      • Count Scale Multiplier 64
    • APPENDIX “B” - SCALING FOR RATE INDICATION 66
      • Rate Scale Multiplier 67
    • APPENDIX “C” - APPLICATION 69
    • APPENDIX “D” - ORDERING INFORMATION 72