Document Outline

• NetLinx Integrated Controller (NI-2000, NI-3000, and NI-4000)
  • Introduction
    • NI-2000 Specifications
    • NI-3000 Specifications
    • NI-4000 Specifications
  • Quick Setup and Configuration Overview
    • Installation Procedures
    • Configuration and Communication
    • Update the Controller and Control Card Firmware
    • Program NetLinx Security into the On-Board Master
  • Connections and Wiring
    • Setting the Configuration DIP Switch (for the Program Port)
      • Baud rate settings
      • Program Run Disable (PRD) mode
      • Using the Configuration DIP switch
    • Modes and Front Panel LED Blink Patterns
    • Wiring Guidelines
      • Preparing captive wires
      • Wiring length guidelines
      • Wiring a power connection
      • Using the 4-pin mini-Phoenix connector for data and power
      • Using the 4-pin mini-Phoenix connector for data with external power
    • Program Port Connections and Wiring
    • RS-232/422/485 Device Port Wiring Specifications
    • ICSNet RJ-45 Connections/Wiring
      • ICSHub OUT port
    • Ethernet 10/100 Base-T RJ-45 Connections/Wiring
      • Ethernet ports used by the Integrated Controllers
    • Relay Connections and Wiring
      • Relay connections
    • Input/Output (I/O) Connections and Wiring
    • IR/Serial Connections and Wiring
    • NetLinx Control Card Slot Connector (NI-4000 unit only)
  • Installation and Upgrading
    • Installing NetLinx Control Cards (NI-4000 Only)
    • Setting the NetLinx Control Card Addresses (NI-4000 Only)
    • Device:Port:System (D:P:S)
    • Removing NetLinx Control Cards (NI-4000 Only)
    • Compact Flash Upgrades
      • Accessing the internal components on an Integrated Controller
      • Installation of Compact Flash upgrades
      • Closing and Securing the Integrated Controller
    • Installing the Integrated Controller into an Equipment Rack
  • Configuration and Firmware Update
    • Communicating with the Master via the Program Port
    • Setting the System Value
      • Using multiple NetLinx Masters
    • Changing the Device Address on a NetLinx Device
      • Recommended NetLinx Device numbers
    • Resetting the Factory Default System and Device Values
    • Obtaining the Master’s IP Address (using DHCP)
    • Assigning a Static IP to the NetLinx Master
    • Communicating with the On-board Master via an IP
    • Verifying the current version of NetLinx Master Firmware
    • Upgrading the On-board Master Firmware via an IP
    • Upgrading the NI Controller Firmware via an IP
      • Upgrading the new NI Controller firmware via an IP
    • Upgrading the Control Card Firmware via an IP
  • NetLinx Security and Web Server
    • NetLinx Security web browser and feature support
    • New Master Firmware Security Features
    • NetLinx Security Terms
    • Accessing the NetLinx Master via its IP Address
    • WebControl Tab
    • Default Security Configuration
    • Security Tab
      • Security tab - Enable Security page
      • Security tab - Add Group page
      • Security tab - Modify Group page
      • Security tab - Group Directory Associations page
      • Security tab - Add User page
      • Security tab - Modify User page
      • Security tab - User Directory Associations page
      • Security tab - SSL Server Certificate page
      • Security tab - Export Certificate Request page
      • Security tab - Import Certificate page
    • System Tab
    • Show Devices Tab
    • Network Tab
    • Master Security Setup Procedures
      • Setting the system security options for a NetLinx Master (Security Options Menu)
      • Adding a Group and assigning their access rights
      • Modifying an existing Group’s access rights
      • Showing a list of authorized Groups
      • Deleting an existing Group
      • Adding a Group directory association
      • Confirming the new directory association
      • Deleting a directory association
      • Adding a User and configuring their access rights
      • Modifying an existing User’s access rights
      • Showing a list of authorized Users
      • Deleting a User
      • Adding a User directory association
      • Confirming the new directory association
      • Deleting a directory association
    • SSL Certificate Procedures
      • Self-Generating a SSL Server Certificate Request
      • Creating a Request for a SSL Server Certificate
      • Importing a CA certificate to the Master over a secure SSL connection
      • Display SSL Server Certificate Information
      • Regenerating an SSL Server Certificate Request
    • Common Steps for Requesting a Certificate from a CA
    • Accessing an SSL-Enabled Master via an IP Address
      • Using your NetLinx Master to control the G4 panel
      • Using your NetLinx Master to control the G3 panel
    • What to do when a Certificate Expires
  • NetLinx Security with a Terminal Connection
    • NetLinx Security Features
    • Initial Setup via a Terminal Connection
      • Establishing a Terminal connection
    • Accessing the Security configuration options
      • Option 1 - Set system security options for NetLinx Master (Security Options Menu)
      • Option 2 - Display system security options for NetLinx Master
      • Option 3 - Add user
      • Option 4 - Edit User
      • Option 5 - Delete user
      • Option 6 - Show the list of authorized users
      • Option 7 - Add Group
      • Option 8 - Edit Group
      • Option 9 - Delete Group
      • Option 10 - Show List of Authorized Groups
      • Option 11 - Set Telnet Timeout in seconds
      • Option 12 - Display Telnet Timeout in seconds
      • Option 13 - Make changes permanent by saving to flash
    • Main Security Menu
    • Default Security Configuration
      • Help menu
    • Logging Into a Session
    • Logout
      • Help Security
      • Setup Security
  • Programming
    • Converting Axcess Code to NetLinx Code
    • Using the ID Button
      • Device:Port:System (D:P:S)
    • Program Port Commands
    • ESC Pass Codes
    • Notes on Specific Telnet/Terminal Clients
      • WindowsTM client programs
      • Linux Telnet client
    • LED Disable/Enable Send_Commands
    • RS-232/422/485 Send_Commands
    • RS-232/422/485 Send_String Escape Sequences
    • IR / Serial Ports Channels
    • IR RX Port Channels
    • IR/Serial Send_Commands
    • Input/Output Send_Commands
  • Troubleshooting