AMD Geode SC1201 - Manual (Page 252)

252 AMD Geode™ SC1200/SC1201 Processor Data Book
Core Logic Module - SMI Status and ACPI Registers - Function 1 32579B
5 THRM_STS. Indicates if PME was caused by activity on THRM#.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[5] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1, (See Note 2 in the
general description of this register above,)
4 SMI_STS. Indicates if PME was caused by activity on the internal SMI# signal.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[4] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above.)
3 GPIO_STS. Indicates if PME was caused by activity on any of the GPIOs (GPIO47-GPIO32 and GPIO15-GPIO0).
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[3] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above).
F0BAR0+I/O Offset 08h/18h selects which GPIOs are enabled to generate a PME. In addition, the selected GPIO must be
enabled as an input (F0BAR0+I/O Offset 20h and 24h).
2:1 Reserved. Reads as 0.
0 PWR_U_REQ_STS. Indicates if PME was caused by a power-up request event from the SuperI/O module.
0: No.
1: Yes.
Write 1 to clear.
For the PME to generate an SCI, set F1BAR1+I/O Offset 12h[0] = 1 and F1BAR1+I/O Offset 0Ch[0] = 1. (See Note 2 in the
general description of this register above.)
Offset 12h-13h GPE0_EN — General Purpose Event 0 Enable Register (R/W) Reset Value: 0000h
In order for the ACPI events described below to generate an SCI, the SCI_EN bit must also be set (F1BAR1+I/O Offset 0Ch[0] = 1).
The SCIs enabled in this register are globally enabled by setting F1BAR1+I/O Offset 0Ch[0] to 1. The status of the SCIs is reported in
F1BAR1+I/O Offset 10h.
15:12 Reserved.
11 Reserved.
10 GPWIO2_EN. Allow GPWIO2 to generate an SCI.
0: Disable.
1: Enable.
A fixed high-to-low or low-to-high transition (debounce period) of 31 µs exists in order for GPWIO2 to be recognized.
The setting of this bit can be overridden via F1BAR1+I/O Offset 15h[6] to force an SMI.
9 GPWIO1_EN. Allow GPWIO1 to generate an SCI.
0: Disable.
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
The setting of this bit can be overridden via F1BAR1+I/O Offset 15h[5] to force an SMI.
8 GPWIO0_EN. Allow GPWIO0 to generate an SCI.
0: Disable.
1: Enable.
See F1BAR1+I/O Offset 07h[3] for debounce information.
The setting of this bit can be overridden via F1BAR1+I/O Offset 15h[4] to force an SMI.
Table 6-34. F1BAR1+I/O Offset: ACPI Support Registers (Continued)
Bit Description