Lenze EPM-H510 - Manual (Page 59)

Commissioning
L
59 EDBEPM-H510 DE/EN/FR 4.0
4.2.2 Project download
The HMI Designer can be used to load the project and update the firmware at the same time.
! Always update the firmware:
– When downloading a project into the keypad for the first time.
– After an update of the “HMI Designer” planning tool.
!
To do this, open the “HMI Designer” and select the “Firmware” option from the “Download”
menu.
!
The firmware will be updated automatically when a new driver is assigned to the project in the
keypad.
!
Please bear in mind that the download process will be considerably slower whilst the firmware
is being updated.
What to do
1. Switch on the PC and start the HMI Designer.
2. Switch on the supply voltage for the keypad.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
2.
The unit is initialised.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
3. After initialisation, select the system page. For
this, touch the display in the
• top right & and bottom left ' or
• top left ( and bottom right ) corners.
The corner to be touched first must not contain
a field for a selctable object.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
The system page appears.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
4. Touch the field “TRAN PAGE” * .
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
4.
The transfer page appears.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
If “WAITING FOR DOWNLOAD“ is
displayed, the keypad is ready for
receiving data from the PC.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
5. Load the project needed from the HMI Designer
to the keypad.
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
+ “HMI Designer - Getting Started”
0
1
2
Port : NET
Driver : CAN Lenze M
Ver : 1.06
Addr : NO ADDRESS
Error : RESET
PROG
ESC
TRAN
PAGE
H510 TRANSFER PAGE
Graphic controller BOOT check: OK
Graphic controller RAM check : OK
*** WAITING FOR DOWNLOAD ***
4
3
“PROGRAMMING MODE” is displayed while downloading data.
6. After the download, the keypad is ready for operation and can exchange data with other participants
through the system bus.
$ $ $ $
Note!
!
Example projects for the keypad can be found in the “HMI Designer” planning
tool under
File , Open ... , Samples .
! The project remains saved after the supply voltage has been disconnected.
Show/Hide Bookmarks