Rockwell Automation 25D PowerFlex 40P Quick Start - FRN 1.xx - 3.xx - Manual (Page 5)

English-5
Category Specification
Agency
Certification Listed to UL508C and CAN/CSA-22.2
Certified to AS/NZS, 1997 Group 1, Class A
Marked for all applicable European Directives
EMC Directive (89/336)
EN 61800-3, EN 50081-1, EN 50082-2
Low Voltage Directive (73/23/EEC)
EN 50178, EN 60204
Certified to ISO 13849-1; Performance Level d (Safety
Category 3).
Meets Functional Safety (FS) when used with the
DriveGuard Safe-Off Option (Series B).
The drive is also designed to meet the appropriate portions of the following specifications:
NFPA 70 - US National Electrical Code
NEMA ICS 3.1 - Safety standards for Construction and Guide for Selection, Installation and
Operation of Adjustable Speed Drive Systems.
IEC 146 - International Electrical Code.
Protection Bus Overvoltage Trip
200-240V AC Input:
380-460V AC Input:
460-600V AC Input: 405V DC bus (equivalent to 290V AC incoming line)
810V DC bus (equivalent to 575V AC incoming line)
1005V DC bus (equivalent to 711V AC incoming line)
Bus Undervoltage Trip
200-240V AC Input:
380-480V AC Input:
460-600V AC Input
P042 = 3 “High Voltage”:
P042 = 2 “Low Voltage”:
210V DC bus (equivalent to 150V AC incoming line)
390V DC bus (equivalent to 275V AC incoming line)
487V DC bus (equivalent to 344V AC incoming line)
390V DC bus (equivalent to 275V AC incoming line)
Power Ride-Thru: 100 milliseconds
Logic Control Ride-Thru: 0.5 seconds minimum, 2 seconds typical
Electronic Motor Overload Protection: Provides class 10 motor overload protection according
to NEC article 430 and motor over-temperature
protection according to NEC article 430.126 (A) (2).
UL 508C File 29572.
Overcurrent: 200% hardware limit, 300% instantaneous fault
Ground Fault Trip: Phase-to-ground on drive output
Short Circuit Trip: Phase-to-phase on drive output
Environment Altitude: 1000 m (3300 ft) max. without derating. Above 1000 m
(3300 ft) derate 3% for every 305 m (1000 ft).
Maximum Surrounding Air Temperature
without derating:
IP20, Open Type:
IP30, NEMA Type 1, UL Type 1:
Flange and Plate Mount: –10 to 50° C (14 to 122° F)
–10 to 40° C (14 to 104° F)
Heatsink:
–10 to 40° C (14 to 104° F)
Drive: –10 to 50° C (14 to 122° F)
Cooling Method
Convection:
Fan: 0.4 kW (0.5 HP) drives and all Flange and Plate drives
All other drive ratings
Storage Temperature: –40 to 85 degrees C (–40 to 185 degrees F)
Atmosphere: Important: Drive must not be installed in an area
where the ambient atmosphere contains volatile or
corrosive gas, vapors or dust. If the drive is not going
to be installed for a period of time, it must be stored in
an area where it will not be exposed to a corrosive
atmosphere.
Relative Humidity: 0 to 95% non-condensing
Shock (operating): 15G peak for 11ms duration (
±
1.0 ms)
Vibration (operating): 1G peak, 5 to 2000 Hz
UL
® C US
TUV
Rheinland
Product Safety
. .
Production inspected
W
E C TUV
Rheinland
. .
Functional
Safety
Bauart geprüft
Type approved
EN 50178