Specifications, Accessories – Banner U-GAGE QT50U Ultrasonic Sensors User Manual
Page 11
Specifications
Sensing Range
200 mm to 8 m (8 in. to 26 ft)
Supply Voltage
10 to 30 V dc (10% maximum ripple); 100 mA max at 10 V, 40 mA
max at 30 V (exclusive of load)
Ultrasonic Frequency
75 kHz burst, rep. rate 96 ms
Supply Protection Circuitry
Protected against reverse polarity and transient overvoltages
Output Protection
Protected against short circuit conditions
Delay at Power-up
1.5 seconds
Output Ratings
150 mA maximum
Off-state leakage current: < 5 μA
Output Saturation NPN: < 200 mV at 10 mA and < 650 mV at 150
mA
Output Saturation PNP: < 1.2 V at 10 mA and < 1.65 V at 150 mA
Output Response Time
100 ms to 1600 ms. See
on page 2.
Temperature Effect
Uncompensated: 0.2% of distance/°C
Compensated: 0.02% of distance/°C
Hysteresis
5 mm
Repeatability
1.0 mm
Minimum Window Size
20 mm
Adjustments
Sensing window limits: TEACH-Mode programming of near and far
window limits may be set using the push buttons or remotely via
Teaching Minimum and Maximum Limits
on page 5).
Indicators
Green Power On LED: Indicates power is ON
Red Signal LED: Indicates target is within sensing range, and the
condition of the received signal
Teach/Output indicator (bicolor Amber/Red):
Amber – Target is within taught limits
OFF – Target is outside taught window limits
Red – Sensor is in TEACH mode
Remote TEACH
To Teach: Connect gray or yellow wire to 0 to +2 V dc; impedance 12
kΩ
Construction
Transducer: Ceramic/Epoxy composite
Housing: ABS/Polycarbonate
Membrane Switch: Polyester
Lightpipes: Acrylic
Operating Conditions
Temperature: −20 °C to +70 °C (−4 °F to +158 °F)
Humidity: 100% maximum relative humidity
Connections
2 m (6.5 ft) or 9 m (30 ft) shielded 5-conductor (with drain) PVC
jacketed attached cable or 5-pin Euro-style quick-disconnect or 5-pin
Mini-style quick-disconnect
Environmental Rating
Leakproof design is rated IEC IP67; NEMA 6P
Vibration and Mechanical Shock
All models meet Mil Std. 202F requirements. Method 201A (vibration:
10 to 60 Hz max., double amplitude 0.06 in, maximum acceleration
10G). Also meets IEC 947-5-2 requirements: 30G 11 ms duration, half
sine wave
Temperature Warmup Drift
Less than 0.8% of sensing distance upon power-up with Temperature
Compensation enabled (see
DIP Switch Selectable Functions
on page 2)
Application Notes
Objects passing inside the specified near limit (200 mm) may produce
a false response.
Certifications
Accessories
5-Pin Mini-Style Cordsets with Shield
Model
Length
Style
Dimensions
Pinout (Female)
MBCC2-506
1.83 m (6 ft)
Straight
7/8-16UN-2B
ø 28 mm max.
(1.1")
61 mm max.
(2.4")
4
3
1
5
2
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Yellow
MBCC2-515
4.57 m (15 ft)
MBCC2-530
9.14 m (30 ft)
U-GAGE QT50UDB Series Sensors with Dual-Discrete Outputs
P/N 110112 Rev. B
www.bannerengineering.com - tel: 763-544-3164
11