Banner SureCross DX80 Wireless Networks - Manual (Page 28)

5 Advanced Setup Instructions and Additional
Information
Refer to the following sections for advanced setup instructions or additional information on Banner's SureCross wireless
technology and its uses.
5.1 DX80 Menu Structure
The Gateways and Nodes each have their own menu structure and options.
5.1 DX80 Gateway Set-up Menu
When power is applied, the DX80 begins running. The display screen auto loops through the RUN menu and
communication begins between the Gateway and Node(s). Auto looping through the RUN menu is the normal operating
mode for all devices on the wireless network.
From the RUN Menu (or any menu), single-click button 1 to advance through the top-level menus. The device auto display
loops through the menu options if either of the RUN, DINFO, or FCTRY menus are selected. If the device is paused on the
SITE, DVCFG, or DERR menu options, the display does not auto loop.
To enter manual scrolling mode, double-click button 2 at the top level menu. Use the instructions shown in the chart below
to navigate the menu system. To return to the top level menus and auto display loop mode, double-click button 2 twice.
The * before the menu name indicates a top-level menu option. The () indicate submenu items.
When using Rotary Dial Addressing Mode, use the left rotary dial to set the Network ID (NID). Once changed, allow five
seconds for the devices to update to the new Network ID.
NOD XX
M XX
R XX
Y XX
G XX
* DINFO * FCTRY * SITE * DVCFG * DERR * RUN
AUTO
DISPLAY
LOOP
AUTO
DISPLAY
LOOP
AUTO
DISPLAY
LOOP
(DEV)
GATEWY
(NID)
XX
(SLID)
XX
(BAUD)
XX
(PRTY)
XX
(DEV)
GATEWY
(RADIO
MICRO)
V 00.0 A
(LCD
MICRO)
V 00.0 A
(DX80
S/N)
(0000)
(DX80
MODEL)
(0000-00)
(PROD
DATE)
(00-00)
Single-click
Button 2
Single-click
Button 2
Single-click
Button 2
Double-click
Button 2
adjust right rotary
switch to survey the
selected Node
Single-click
Button 2
Double-click
Button
2
Double-click Button 2
NOD XX
EC XX CLEAR
ERR
ERASED
ERR
DISABL
* ERROR
DISABL IGNORE
Next
Device
Single-click Button 1 to advance through menu
AUTO
DISPLAY
LOOP
Single-click
Button 2
Single-click
Button 2
Single-click
Button 2
Single-click
Button 2
Single-click
Button 2
Single-click
Button 2
New Error
Detected
adjust the rotary
switches to survey
the selected Node
(DEV)
I/O XX
GATEWY
NID XX
ON/OFF
(DEV)
I/O XX
GATEWY
NID XX
ON/OFF
Even
None
Odd
Single-click
Button 2
Single-click
Button 2
SAVES
DISPLAYED
VALUE
Single-click B1
19200
9600
38400
Single-click
Button 2
Single-click
Button 2
SAVES
DISPLAYED
VALUE
NEW XX
Single-click
Button 2
Single-click
Button 2
adjust rotary switches
to set the network ID
SAVES NEW
VALUES
CUR XX
Single-click
Button 2
Single-click
Button 2
adjust rotary switches
to set slave ID, using
button 1 to select the
digits
SAVES NEW
VALUES
(NID) (SLID) (BAUD) (PRTY)
Network ID Slave ID Baud Rate Parity
Single-click B1
NEW XX
Single-click
Button 1
Single-click
Button 1
Single-click
Button 1
Single-click
Button 1
Single-click Button 1 to advance through menu
(NAME)
XXXXXX
XXXXXX
Single-click Button 1 to advance through menu
CUR XX
Double-click Button 2
Double-click
Button 2
* Set to 000000 to use the serial number.
Device Info Factory Info Site Survey Device Config Device Error
16
8
32
Single-click
Button 2
Single-click
Button 2
SAVES
DISPLAYED
VALUE
Single-click B1
(MAXN)
Timing
48
MANUAL
AUTO AUTO
SET
Single-click
Button 2
Single-click
Button 2
Single-click B1
(XADR)
Extended Addressing
XADR
ADJUST ROTARY
SWITCH TO
SET XADR
Single-click
Button 2
XXXXXX Single-click B1
Single-click
Button 2
CONFRM
XADR
XXXXX
NETWRK
Single-click
Button 2
BINDNG
Single-click
Button 1 or 2
Reboot
SAVED
*
XXXXXX
SureCross Wireless I/O Networks
28