Tweco 130i Transarc Service Manual User Manual

130i service manual, Transarc, Welding inverter

Advertising

Table of contents

Document Outline

0-5143-CCr
SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
- 1.04 Symbol Chart
- 1.05 Servicing Hazards
- 1.06 EMF Information
SECTION 2: INTRODUCTION
- 2.01 How to Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt of Equipment
- 2.04 Description
- 2.05 Transportation Methods
SECTION 3: SAFETY AND INSTALLATION
- 3.01 Duty Cycle
- 3.02 Specifications
- 3.03 Environment
- 3.04 Location
- 3.05 High Frequency Introduction
- 3.06 High Frequency Interference
- 3.07 Electromagnetic Compatibility
SECTION 4: INSTALLATION, OPERATION AND SETUP
- 4.01 Transarc 130i Power Source Controls, Indicators and Features
- 3.07 Shielding Gas Regulator Operating Instructions (where supplied)
- 3.08 Setup for TIG (GTAW) Welding
- 3.09 Foot Control Part No. W4015800 (Optional Accessory)
- 3.10 Setup for Manual Arc (MMAW) Welding
SECTION 5: THEORY OF OPERATION
- 5.01 Inverter Design
SECTION 6: TROUBLESHOOTING
- 6.01 Basic Troubleshooting-Power Source Faults
- 6.02 Advanced Troubleshooting
- 6.03 Test Equipment and Tools
- 6.04 Visually Inspect
- 6.05 Preliminary DC Bus measurement of the main inverter board
- 6.06 Preliminary check of the main inverter board
- 6.07 Check main input rectifier
- 6.08 DC Bus voltage measurement
- 6.09 PCB Connectors
- 6.10 DIP switch settings, Control PCB
- 6.11 Calibration
- 6.12 Main Circuit Description
- 6.13 Circuit Diagram
SECTION 7: DISASSEMBLY PROCEDURE
- 7.01 Safety Precautions for Disassembly
- 7.02 Case Removal
- 7.03 Control PCB Removal
- 7.04 Solenoid Valve and Current Transformer Output Removal
- 7.05 Display PCB Removal
- 7.06 Front Panel assembly Removal
- 7.07 Rear Panel Removal
- 7.07 Base Panel Removal
SECTION 8: ASSEMBLY PROCEDURES
- 8.01 Installing Base Panel
- 8.02 Installing Rear Panel
- 8.03 Installing Front Panel assembly
- 8.04 Installing Display PCB
- 8.05 Installing Solenoid Valve and Current Transformer Output
- 8.06 Installing Control PCB
- 8.07 Installing Case
SECTION 6: KEY SPARE PARTS
- 9.01 Power Source
- 9.02 TIG Torch W4013804 (where supplied)
- 9.03 Stick Electrode Holder with Trigger Switch 646762(where supplied)
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY – January 2013
WARRANTY SCHEDULE – January 2013
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
SECTION 3: INSTALLATION, OPERATION AND SETUP
- 3.17 Setup for TIG (GTAW) Welding
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY - JULY 2010
WARRANTY SCHEDULE - JULY 2010
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION

Popular Brands

Popular manuals