Great Plains PTO Kits 2-3-Section - Manual (Page 26)

411-015M Table of Contents Index 2014-09-10
22 2- & 3-Section YP PTO Pumps Table of Contents Index Great Plains Manufacturing, Inc.
PTO Maintenance
Oil and Filter Change
Oil Fill
Refer to Figure 17 and Figure 18
A dry or fully drained system may require as much as
20 gallons (76 liters) of oil to charge the cooler, pump,
motor(s), hoses, filter and valve, and leave 13.5 gallons
(51 liters) in the reservoir.
Before adding oil, check that the drain plug is secure,
and that there are no signs of leaks in hoses or at any
system fittings.
Oil Specification
10W-30 good quality mineral base hydraulic fluid,
viscosity 70 to 250 SUS at 210
°F (100°C)
Remove the filler cap . Add oil until the oil level in the
reservoir, as observed on the sight gauge , reaches the
fill line on the decal (the top edge of the horizontal
mid-border of the decal). The fill line is 10.73 inches
(27.3 cm) above the reservoir bottom. If the 858-029C
decal requires replacement, adjust the center border line
to this height.
Operate the PTO system briefly, or until the reservoir
level stops changing. See “PTO Operation” on page 8
for operations.
Recheck the sight gauge. As necessary, add oil to fill
line.
Oil and Filter Change
At a regularly scheduled oil change, also change the
filter. At initial system flush, no filter change is required.
Refer to Figure 18 and Figure 17
1.
Wait for the oil to cool before changing the oil.
2. Place a container with at least a 20 gallon (76 liter)
capacity under the drain plug
of the reservoir.
3. Carefully remove the drain plug.
4. Allow several minutes for oil in the filter to drain into
and out of the reservoir. Change filter as required.
See page 23 for filter size. Seat filter per
instructions on filter.
5. Thread the plug back into the reservoir. Seating
torque is 27 to 43 foot-pounds (37 to 58 N-m).
85 8- 030 C
Al l dr ive line gua rds , tr ac tor
an d e quipmen t s hields in plac e
PT O pump assemb ly s ec ure ly
attached with torque ar
m and clamp
bolts proper ly torqued
RO TATING DRIVELINE - CONT ACT CAN CA
USE DEA TH
KEEP A W AY!
DO NO T OPERA TE WITHOUT -
DA NGE
R
85 8-0 29C
CAP ACITY = 13.5 U
.S . GALS
USE ANY HIG
H QU ALITY M INE RA L B ASED
HYDRA ULIC FLUID
WITH A VISCOSITY RA
TING
OF 1 0W- 30 . O IL MUS T B E CL EA N AND FR EE
FR OM DIR T OR C ON TA M INANT PA RT IC LE S TO
PREVENT D
AMA GE TO PUMP AND
MO TOR .
REPLA CE FIL TER ELEMEN T AFTER EVER Y
15 0 OPERA TING HOU RS OR 2 YE AR S SER VIC E.
LEVE L T OOL BAR B EFO RE CHEKI NG OIL L EVE L
OIL FILL LINE
858-0 04C
Re ad Ow ner’ s M anu al BEF ORE ope rating m ac hine .
Keep tra ctor a t IDL IN G SPEED and slo wly en gage PT O
to pre vent da ma ge to Hy drauli c M otor
Ke ep R adiator clea n and f ree of fo reig n m atter to
pre vent o verheating. Do NO T o pe rate w ith hydr aulic o il at or abo ve 1 80°F .
HO T FLUID HAZARD
WARNING
818-2 40C R ev. A
To a void Injur
y or
Mac hine Dama
ge:
·Operate onl
y with 1000 rpm PT
O
CAUTION
2
3
Hot Surface and Hot Fluid Hazards:
Assess the reservoir temperature before adjusting oil level.
Draining excess hot oil could result in a severe burn. If the
PTO has been operated recently, the oil temperature could be
as high as 180
°F (82°C).
Figure 17:
Oil Filler Cap and Filter
34843
1
2
3
Figure 18:
Oil Drain Plug
34850
858-03 0C
All dr iveline guards , tr actor
and e quipment shields in place PT O pump assemb
ly securely
attached with torque ar
m and clamp
bolts pro per ly torque d
RO TATING DRIVELINE - CONT ACT CAN CA
USE DEA TH
KEEP A W AY !
DO NO T OPERA TE WITHOUT -
DANGER
85 8-029C
CAP ACITY = 13.5 U
.S . GALS
USE ANY HIGH Q
UALITY MINERAL BA
SED
HYDRA ULIC FLUID
WITH A VISCOSITY RA
TING
OF 10W -30. OIL MUST BE CLEAN AND FRE
E
FR OM DIR T OR CONT
AMIN ANT P AR TICLES TO
PREVENT D
AMA GE TO PUMP AND MO
TOR.
REPLA CE FIL TER ELEMENT AFTER EVER
Y
150 OPERA
TING HOURS OR 2
YEARS SER
VICE.
LEVEL TOOLBAR BEFORE CHEKING OIL
LEVE L
OIL FILL LINE
858-004C
Read Owner’ s Ma nual BEFORE oper
ating machine .
Keep tr actor at IDLING SPEED and slo
wly engage PT O
to pre vent damage to Hy
draulic Motor
Keep Radiator clean and free of f
oreign matter to
pre vent o verheating. Do NO T oper ate with h ydr aulic oil at or abo ve 180°F .
HO T FLUID HAZARD
WARNING
818-240C Re v. A
To a void Injur
y or
Mac hine Dama
ge:
·Operate onl
y with 1000 rpm PT
O
CAUTION
1
1