Great Plains CDA600 Parts Manual - Manual (Page 27)

Revision Comments Part Description Part No. Ref.
Image No. dwg34149
HHCS M12X1.75X60 GR8.8 802-979C 1.
WASHER FLAT M12 - OD36MM 804-263C 2.
PLATE BENT CULT SECTION DEPTH 270-438D 3.
HHCS M12X1.75X30 GR8.8 802-458C 4.
STANDOFF 1 OD X 1 X 5/8 270-439D 5.
NUT HEX NYLOCK M12X1.75 PLT 803-281C 6.
FRAME CENTER WLDMT 270-117H 7.
PIN 25MM X 53MM FIXED 270-106H 8.
ROLL PIN 8MM X 50MM PLT 805-452C 9.
LINK ARM WLDMT STRAIGHT 270-091H 10.
NUT HEX NYLOCK M12X1.75 PLT 803-281C 11.
Refer to Coulter Toolbar Assembly for
breakdown
CULT DISC ASM CENTER FRONT 270-197V 12.
Refer to Coulter Toolbar Assembly for
breakdown
CULT DISC ASM CENTER REAR 270-198V 13.
Refer to Hydraulic Cylinder (810-777C)
for breakdown
CYL REP 70MMX200MMX36MM MEMORY 810-777C 14.
PIN 25MM X 100MM NON-ROTATE 270-153H 15.
PIN 25MM X 65MM NON-ROTATE 270-010H 16.
Refer to Hydraulic Cylinder (810-756C)
for breadown
CYL REP 60MM X 125MM X 32MM 810-756C 17.
PIN 25MM X 100MM NON-ROTATE 270-153H 18.
TOOLBAR LEVELING BOARD CENTER 270-074H 19.
HHCS M16X2.0X35 GR8.8 802-966C 20.
MOUNT TOOLBAR WLDMT 270-057H 21.
HHCS M16X2X30 GR8.8 802-981C 22.
HHCS M16X1.5X50 GR8.8 802-946C 23.
MOUNT TOOLBAR PLASTIC 270-001D 24.
RETAINER BRG WLDMT 270-092H 25.
SCRAPER TIRE 270-240D 26.
WALKBOARD 270-047H 27.
WASHER FLAT M12 PLT 804-246C 28.
HHCS M12X1.75X40 GR8.8 802-977C 29.
BRACKET TIRE SCRAPER RHT 270-449D 30.
MOUNT TIRE SCRAPER CENTER 270-448D 31.
BRACKET TIRE SCRAPER 270-440D 32.
U-BOLT M16-2.00 X 102 X 140 806-226C 33.
WASHER SPRING LOCK M16 PLT 804-187C 34.
NUT HEX NYLOCK M16X2.00 GRB PT 803-282C 35.
HHCS M16X2X25 GR8.8 842-087C 36.
WASHER 3/8BSPP BONDED 841-793C 37.
PLUG 3/8MBSPP HOLLOW HEX 841-786C 38.
AD 3/8MBSPP 3/8MBSPP 841-801C 39.
EL ADJ 3/8MBSPP 3/8MBSPP 841-804C 40.
07/23/14 - 27 - 270-600P
Table of Contents Part Number Index
Frame
Front Center Section Assembly
(Applies to CDA600 only)