Two Brothers Racing Carbon End Cap 005-7-1CF-KIT for 005-P1C-X Tip - Manual

Installation Instructions
Carbon end Cap
Part # 005-7-1CF-KIT-2
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely
cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat
cycles, this is a normal characteristic of high quality stainless steel. Clean using a mild water based
spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep
blue/purple through amber after a few heat cycles. This is a normal characteristic of high quality
titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to
factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner
or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or
polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good condition and
not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you
need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish
with a soft, clean cloth. Always make sure the fiberglass packing inside is in good condition and not
burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you
need to easily do it yourself.
Repack all road canisters at the first signs of packing material deterioration. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack
of cooling air can quickly burn through the canister material. Two Brothers Racing does not provide a
warranty for burned canisters.
IMPORTANT - PLEASE READ CAREFULLY
Two Brothers Racing products are intended for closed course
competition purposes only.
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to
install this performance part, please consult with your local motorcycle
dealer. Read all instructions first before starting installation. Make sure
the motorcycle and exhaust system are completely cool before starting
the installation. Also, make sure the bike is secure on a centerstand
or ideally a service lift during installation. Be sure to save all stock
components for possible use later.
Two Brothers Racing products are intended for closed course competition purposes
only, and therefore are sold “as is” without warranty. Two Brothers Racing specifically
disclaims any warranties of merchantability or fitness for a particular purpose and
disclaims all responsibility for consequential and incidental damages or any other
losses arising from the use of these products or parts. Not tested for use with OEM or
aftermarket accessories.
Warranty Information
1. Make sure motorcycle is completely cool before starting the installation.
Make sure the motorcycle is secure on a rearstand or ideally a service lift.
Note: Muffler does not need to be removed for install.
2. Remove the original magnesium TBR muffler cap by loosening and removing
the six stainless steel torx drive screws.
3. Install supplied TBR P1C-X muffler tip. Position indicator marks so that they
are aligned.
4. Install retaining ring using two of the supplied stainless steel torx screws.
Make sure indicator mark is visible in the triangle before tightening. After
alignment is verified fully tighten screws.
5. Place new carbon fiber cap onto muffler assembly. Attach by evenly
tightening the remaining four torx screws.
6. Before you run the bike, clean off all fingerprints and dirt using a non abrasive
towel or shop rag.
Qty. Description Part Number
1 M-2 Vertical CF End Cap 005-7-1CF
1 Race Tip Restraint for Carbon 005-P1C-RE
1 Race Pipe Power Tip for CF End 005-P1C-X
6 Stainless Steel Head Cap Screw 005-SHA616SS
1 T20 Torx Hex Key 005-9-15820