Speaker impedance :5p ihp, User presets fdfleiiiet, Remote control amp id fieiiote:: fihf – Yamaha HTR-6080 User Manual
Page 95: Setting remote control amp id codes, Notes
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advanced setup
See page 90 for the operation of the advanced ^etifp.
■ Speaker Impedance :5P IHP =
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices:
8fi MIN,
6fi MIN
• Select “8£1 MIN" to set the speaker impedance to 8 £1.
• Select “6£1 MIN” to set the speaker impedance to 6 £1.
SP IMP.
SftMlN
6f2MlN
Speakor
Impodnnce level
From
If you use one set {A or B ),
the impedance of each
speaker mu si be S Q or
higher.
If you use Iwo sels {A and
B). ihe impedance of each
speaker must be 16 Q or
hisher."*
Center
Surround
■ The impedance of ecidi
speaker musi be S Q or
. higher.
Surround back
From
If you use one sel (A or B ).
ihe impedance of each
speaker must be 4 Q or
higher.
If you use iwo sets (A and
B). the impedance of each
speaker must be S Q or
hisher.
Center
Surround
The impedance of each
speaker musi be 6 Q or
higher.
Surround back
The Canada model cannot use two separate speaker systems
(A and B) simultaneoiisly when “SP IMP.” is set to “8Q MIN”
■ User presets FdflEiiiET
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 101).
Choices:
CANCEL,
RESET
• Select “CANCEL” not to reset any parameters of this
unit.
• Select
¡
q
reset the parameters of this unit.
■ Remote control AMP ID FiEiiOTE:: FiHF-'
Use this feature to set the AMP ID of this unit for remote
control recognition. This feature is useful when you
operate this unit and the other Yamaha receivers/
amplifiers in the same room separately.
Choices:
ID1,
ID2
• Select “ID I” when the remote control AMP ID code is
set to“()()()()l”.
• Select “1D2” when the remote control AMP ID code is
set to “()00()2”.
Setting remote control AMP ID codes
You need to set the remote control AMP ID code for the
remote control.
1 Press (S)CODE SET using a ballpoint pen or
a similar object.
The
(y)TRANSMIT
indicator on the remote control
flashes twice.
B E B E
TRAIÍSMIT
Flashes
Press the numeric buttons (d)) to enter the
code number “00001 ” or “00002”.
The
©TRANSMIT
indicator on the remote control
flashes twice, and the A.MP ID code is changed.
CLASSICAL UVEICLUB ENTERTAIN MOVIE
0
dX ©
©
STEREO ENHANCEy^TRAIGHT PURESRECT
© ® ©
©
JR. BECCDE MIGHT
TRApjSitllT
Flashes
AMP ID
code '1
Function
Remote
control AMP
ID '2
Ü0001
To operate this unii using
IDi
(iniliai selling) ihe defauli eode.
liniiiaì selling)
00()02
To operate this unii using
an aitemalive code.
ID2
''1 The remote control setting
’N The setting of this unit
Notes
■ This setting completely resets all the parameters of this unit
ineltiding the “SET MENU” parameter.s.
■ The initial factory settings are activated next time you turn on
this unit.
91
En