KEYENCE BL-1300 Series - Manual (Page 2)

2 E BL-1300-IM
 For proper use of this product
 UL Certificate
The BL-1300 Series is an UL/c-UL certified product.
•
UL File No. E207185, E167973
• UL category NRAQ/NRAQ7, NWGQ2/NWGQ8
Be sure to observe the following installation and environment conditions.
•
Be sure to use a power supply that provides class 2 output as defined
in NFPA70 (NEC: National Electrical Code).
• Pollution degree 2
• Overvoltage category I
 FDA regulations
The BL-1300 Series is classified as class 2 laser product. The
classification is based on IEC60825-1 following the Laser Notice No. 50
from FDA (CDRH).
 FCC regulations
The BL-1300 Series complies with the following FCC EMI regulations.
•
FCC Part 15 Subpart B, Class B digital devices
 Canada IC (Industry Canada) regulations
The BL-1300 Series conforms to the following IC EMI regulations.
•
ICES-003, Class B digital apparatus
 CE marking
The BL-1300 Series complies with the following essential requirements
of the EU Directives.
•
EMC Directives (2004/108/EC)
• Low-voltage Directives (2006/95/EC)
The following harmonized standards are applied to these products in
order to confirm the compliance.
•
Applicable standards (EMI) EN55011, Class A
EN55022, Class B
• Applicable standards (EMS) EN61000-6-2
EN61000-6-1
* The length of the communication and power cables should be less than 30
m.
CAUTION
Precautions on use
• The BL-1300 uses a 5 V DC power supply. Using a
different voltage level may damage the unit. When using
the KEYENCE power supply unit N-R2, N-R4, N-UB, N-L1,
NX-50 Series or DV-90 Series, select the voltage level
which can be supplied by the power supply unit. If a
nonconforming power supply is connected, the BL-1300
may be damaged.
• Before connecting or disconnecting the cable, be sure
to turn off any device connected to the BL-1300 Series.
Otherwise, the BL-1300 Series may be damaged.
• Do not disassemble or modify the BL-1300 Series, as
this may cause product failure.
• Locate cables as far as possible from high-voltage
lines and power lines. Otherwise, generated noise may
cause product failure or malfunctions.
• Before mounting the BL-1300 Series, insulate the
mounting location. Otherwise, generated noise may cause
product failure or malfunctions.
• The BL-1300 is a
precision instrument.
Dropping the unit or
subjecting it to shock
may cause damage. Be
careful when
unpacking, carrying, an
mounting it. Do not
hold the units by their
cables.
• Do not hold the units by
their cables when carrying
them. The units may hit
each other and become
damaged.
If abnormal conditions are encountered
If the following conditions are encountered, turn off the
power supply unit immediately. Continuing to use the BL-
1300 Series under abnormal conditions may cause fire,
electric shock, or product failure. Contact your nearest
KEYENCE sales office (listed at the end of this manual)
for repairs.
• Water or foreign matter enters the BL-1300 Series.
• The BL-1300 Series is dropped or the housing is
damaged.
• The BL-1300 Series produces smoke or an abnormal
smell
Precautions on Regulations and Standards
Package Contents List
Main unit
Instruction manual
Mounting bracket
BL-1300/1301/1300HA/
1301HA/1370/1371
BL-1350HA/1351HA
BL-1300/1301/1300HA/
1301HA/1370/1371
BL-1350HA/1351HA
Mounting bracket: 1 Mounting bracket A and B: 1 each
Insulating spacer: 4
Washer: 4
Mounting screw (M3): 2
Laser warning seal set: 1
BL- 1300/1301/1300HA/
1301HA/1370/1371
BL-1350HA/1351HA
1
Laser Bar Code Reader BL-1300 Series
Instruction Manual
„ General precautions
• Do not use this product for the purpose to protect a human body or
part of a human body.
• This product is not intended for use as an explosion-proof product. Do
not use this product in a hazardous location and/or potentially
explosive atmosphere.
• We recommend that you take substantial safety measures to avoid
any damage in the event a problem occurs. • If the BL-1300 is modified or used in any way other than described in
the specifications, its function and performance cannot be guaranteed.
• When the BL-1300 is used in combination with other instruments, the
function and performance may be effected by operating conditions and
the surrounding environment.
• It is prohibited to use or copy all or any part of this manual without prior
approval.
• The information contained in this manual is subject to change without
notice.
„ Safety precautions on laser product
The "BL-1300 Series Laser Barcode Reader" uses a visible laser light
source.
The BL-1300 Series barcode readers are equipped with the following
safety measures.
• Laser radiation emission warning LED (LASER LED) During laser emission, the LASER ON LED illuminates. The LED ON
status can be clearly visible through protective eyewear; specifically
designed for the wavelength of 660nm.
• Laser forced OFF command Sending the laser forced OFF command to the BL-1300 can inhibit
emission of laser beams. When working near the laser transmitter, be
sure to use the laser forced OFF command to avoid looking into the
laser beams.
* When this command is selected, the bottom STABILITY LED flashes.
„ IEC warning/explanatory label locations
Use the suitable IEC warning/explanatory label included in the package
of this product according to the countries and/or regions where this
product is used.
In this case, it can be affixed on the IEC warning/explanatory label,
which has already been affixed to this product.
DANGER Failure to follow these instructions may lead to death or
serious injury.
WARNING Failure to follow these instructions may lead to injury.
CAUTION Failure to follow these instructions may lead to product
damage (product malfunction, etc.).
Note Provides additional information on proper operation.
TIPS Indicates useful information or information that aids
understanding of text descriptions.
Safety information for BL-1300 Series
WARNING Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
96M12614
Model BL-1300, 1301, 1300HA, 1301HA, 1350HA, 1351HA, 1370, 1371 Wavelength 660 nm Output 85 μW Pulse duration 112 μs
Laser Class FDA (CDRH)
Part 1040.10 Class 2 Laser Product IEC 60825-1 Class 2 Laser Product
WARNING
• Follow the instructions mentioned in this manual. Otherwise, injury to the human body (eyes and skin)
may result.
Precautions on class 2 laser products • Do not stare into the beam.
• Do not direct the beam at other people or into areas
where other people unconnected with the laser work
might be present. • Be careful of the path of the laser beam. If there is a danger that the operator may be
exposed to the laser beam reflected by specular or
diffuse reflection, block the beam by installing an
enclosure with the appropriate reflectance.
• Install the products so that the path of the laser beam is not as the same height as that of human eye. • Do not disassemble this product. Laser emission from this product is not automatically stopped when
it is disassembled.
BL- 1300/1301/1300HA/ 1301HA/1370/1371 BL-1350HA/1351HA