Part names and functions, Connection and wiring method, Connection connector pin layout – KEYENCE BL-1300 Series User Manual

Page 3: Connecting the power supply, Wiring in1/in2 input pins, Wiring out1/out2/out3/out4 output pins, Wiring rs-232c

Advertising
background image

3

E BL-1300-IM

Connection connector pin layout

* The shield line is directly connected to the common GND.

Connecting the power supply

Connect a cable with a
length of 4.8 m or less.

Wiring IN1/IN2 input pins

•

The IN1 (timing) input is used to trigger the BL-1300 Series to read
barcodes (to emit a laser beam).

•

The IN2 (preset) input is used to trigger the BL-1300 Series to register
barcode data.

IN1/IN2 input is performed by no-voltage input.

Wiring OUT1/OUT2/OUT3/OUT4 output pins

•

OUT1 (OK) is used as output indicating that reading is successfully
completed and that the comparison and matching with preset data is
judged as OK.

•

OUT2 (NG/ERROR) is used as output indicating that reading has
failed and that the comparison and matching with preset data is judged
as NG.

•

OUT3 (ERROR) is used as output indicating that reading has failed.

•

OUT4(BUSY) is output any time the trigger input cannot be accepted,
such as cases where the BL-1300 Series is at initial start-up or in
setting mode, the motor/laser is damaged, the motor/laser is locked, or
the number of rotations of the motor is changed.

The output form of each signal is NPN open collector.

Wiring RS-232C

When connecting the BL-1300 Series to the PC, connect as shown
below.

Part Names and Functions

Number

Name

Function

1

LASER LED

Lit when laser beams are emitted.

2

OK/NG/ERR LED

• When OK output is ON: The green LED

lights.

• When NG output is ON: The orange LED

lights.

• When ERR output is ON: The red LED

lights.

3

TIMING LED

Lit when trigger input is ON.

4

STABILTY LED

Displays the reading stability and the BL-
1300 operating status.

5

TEST SWITCH

This switch is used to perform the following
operations.
• If this switch is pressed once shortly, a

barcode is read once.

• Starting and canceling the test mode
• Start reading of batch set bar codes
• Registering preset data
• Canceling PLC link errors
• Fixing the communication setting to the

initial value when setting transmission and
reception

6

Transmitter/receiver

Receives the emitted and reflected light of
laser beams and reads barcodes.

7

Connector

Used to connect to the communication unit.

8

Cable

Cable length is 2 m.

Connection and Wiring Method

Pin number

Symbol

Explanation

1

OUT1

Output pin 1 (initial value OK output)

2

OUT2

Output pin 2 (initial value NG/ERROR
output)

3

TXD

RS-232C transmission

4

CTS

RS-232C transmission permitted

5

OUT4

Output pin 4 (initial value BUSY output)

6

IN2

Input pin 2 (initial value PRESET input)

7

RXD

RS-232C reception

8

RTS

RS-232C reception permitted

9

OUT3

Output pin 3 (initial value ERROR output)

10

IN1

Input pin 1 (initial value TIMING input)

11

+5V

+5V power supply

12

GND (SG)

Common GND

6. Transmitter/receiver

7. Connector

8. Cable

8. Cable

1. LASER LED
2. OK/NG/ERR LED

3. TIMING LED

4. STABILITY LED

5. TEST SWITCH

6. Transmitter/receiver

7. Connector

6

10

5

9

4

2

1

8

12

11

3

7

Cable head cross-section view
RP17-13PA-12PC plug (male)

Manufactured by Hirose Electric Co., Ltd.

Note

• Reverse connection of the power supply is strictly

prohibited. This may cause product failure.

• Use a stable power supply of 5V DC

5%. Using a

power supply outside this range may cause product
failure.

GND

+5V

12

11

5 VDC

+

10 k

Ω

100

Ω

TIM

GND

12

6,10

4.7 k

Ω

5 VDC

In

te

rn

a

l ci

rc

u

it

Contact

or

non-contact

GND

OK/NG

12

+

1, 2,
5, 9

3.3 k

Ω

6.8 k

Ω

33 V

Load

* Rated load: 24V DC (30 mA) or less

In

te

rn

a

l ci

rc

u

it

BL-1300 Series

PC

3

4

7

8

11

12

TxD

CTS

RxD

RTS

GND

+5V

2

7

3

8

5

4

6

+

RxD (RD)

RTS (RS)

TxD (SD)

CTS (CS)

GND (SG)

DTR (ER)

DSR (DR)

Round
connector
12-pin (male)

D-sub9 pin
(female)
#4-40 screw

Advertising