Marantz NR1501 - Manual (Page 35)

NAMES AND FUNCTIONS
31
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
ADV
ANCED
OPERA
TION
ENGLISH
REMOTE CONTROLLER
OPERATION
NORMAL MODE
WHEN OPERATING MARANTZ AV EQUIPMENT
PRODUCTS
This remote controller is preset with a total of 10
types of remote codes, including Marantz BD (Blu-
ray), GAME, DVD, VCR (VCR deck), DSS (satellite
broadcasting tuner), TUNER, CD, AUX1, AUX2, and
AMP (amplifi er).
1.
Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the
source that was pressed.
To change the amplifi er on other source,
press the SOURCE button twice (double-
click). The code is sent, and then the
amplifi er source changes to DVD.
PRESET MODE
WHEN OPERATING NON-MARANTZ AV
EQUIPMENT PRODUCTS
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, CD, DVD, BD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers,
and other settings.
Remote
controller
source name
Corresponding
preset code
Device name
TV TV Television
BD
DVD
DVD DVD player
CD CD CD player
DSS SATELLITE
Satellite
broadcasting
tuner equipment
Importants
• Some codes may be not match your equipment.
• The preset codes do not cover full functions.
• When the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
1.
2.
1.
1.
Press and hold down the SOURCE button for
the appliance which should be controlled and
press SET button until the SEND indicator
blinks twice. Then SET indicator fl ashes.
In case of TV, press and hold down the TV
Power On/off button and SET button.
2.
Press the 4-digit code by numeric buttons for
appliance (code table at the end of this book)
When the procedure is successful, the
SEND indicator will blink twice.
Note
If the indicator did not blink twice, then repeat steps
1 through 2 and try entering the same code again.
SCANNING THE CODE TABLE
2.
3.
3.
2.
5.
2.
1. Switch on the appliance which should be
controlled.
2. Press and hold down the SOURCE button
for appliance which should be controlled
and press SET button until the SEND
indicator blinking twice. Then SET indicator
fl ashes.
In case of TV, press and hold down the TV
Power On/off button and SET button.
3.
Aim the remote control at the appliance
and slowly alternate between pressing
INPUT
3 button and the SOURCE ON/OFF
button for the appliance.
In case of TV, press INPUT 3 button and the
TV Power On/off button alternately.
4.
Stop when the appliance turns off.
5. Press ENTER button once to lock in the
code.
CHECKING THE CODE
1.
1.
2.
3.
4.
1.
1. Press and hold down the SOURCE button
for appliance which should be controlled
and press SET button until the SEND
indicator blinking twice then SET indicator
fl ashes.
In case of TV, press and hold down the TV
Power On/off button and SET button.
2.
Press the INFO button.
The SEND indicator will blink twice.
3.
To view the code for first digit, press 1
once.
Wait 3 seconds, count the SEND indicator
blinks (e.g. 3 blinks = 3) and write down the
number.
Note
If a code digit is “0”, the SEND indicator will not
blink.
4.
Repeat step 3 three more times for
remaining digits. Use 2 for the second digit,
3 for the third digit, and 4 for the fourth
digit.
RESETTING THE CODE
1.
1.
2.
1.
1. Press and hold down the SOURCE button
for appliance which should be controlled
and press SET button until the SEND
indicator blinking twice.
Then SET indicator fl ashes.
In case of TV, press and hold down the TV
Power On/off button and SET button.
2.
Press the below codes to reset.
TV : 1000
DVD : 2000
CD : 3000
DSS : 4000
BD : 5000
The indicator will blink twice.
Note
After this procedure, the selected SOURCE button
is set initial code.
ADVANCED OPERATION