Document Outline

• Guaranty and Declaration
• Safety Requirement
  • General Safety Summary
  • Safety Terms and Symbols
  • Allgemeine Sicherheits Informationen
  • Sicherheits Begriffe und Symbole
  • General Care and Cleaning
  • Environmental Considerations
• DSG3000 Series Overview
• Document Overview
• Chapter 1 Quick Start
  • General Inspection
  • Appearance and Dimensions
  • Front Panel Overview
  • Rear Panel Overview
  • To Use DSG3000 for the First Time
    • To Connect the Power Supply
    • Power-on Inspection
    • To Set the System Language
  • To Replace the Fuse
  • User Interface
    • Normal Display Mode
    • Parameter Zoom-in Mode
  • To Use the Built-in Help System
• Chapter 2 Front Panel Operations
  • To Set the Frequency Parameters
    • Frequency
    • Frequency Offset
    • Phase Offset
  • To Set the Amplitude Parameters
    • Amplitude
    • Amplitude Limit
    • Amplitude Offset
    • Attenuation Mode
    • Attenuation
    • ALC
    • Hold Mode
    • Flatness Calibration
    • Amplitude Unit
  • Sweep
    • Sweep Manner
    • Sweep Direction
    • Sweep Type
      • List Sweep
      • Step Sweep
    • Sweep Mode
    • Single Sweep
    • Reset Sweep
    • Trigger Mode
  • Modulation
    • Amplitude Modulation (AM)
      • To Enable AM
      • To Select the Modulation Source
      • To Set the Modulation Depth
      • To Select the Modulation Waveform
      • To Set the Modulation Frequency
    • Frequency Modulation (FM)
      • To Enable FM
      • To Select the Modulation Source
      • To Set the Frequency Deviation
      • To Select the Modulation Waveform
      • To Set the Modulation Frequency
    • Phase Modulation (ΦM)
      • To Enable ΦM
      • To Select the Modulation Source
      • To Set the Phase Deviation
      • To Select the Modulation Waveform
      • To Set the Modulation Frequency
    • Pulse Modulation
      • To Enable Pulse Modulation
      • To Select the Modulation Source
      • To Select the Pulse Mode
      • To Set the Pulse Period
      • To Set the Pulse Width
      • To Select the Trigger Mode
      • Pulse Output
      • Trigger Delay
      • To Set the Polarity
      • Pulse Train List
    • I/Q Modulation (Option IQ-DSG3000)
      • To Enable I/Q Modulation
      • To Select the Modulation Source
      • Baseband Signal
  • LF Output
    • To Enable the LF Output
    • To Set the LF Parameters
      • To Select the LF Waveform
      • To Set the LF Amplitude
      • To Set the LF Frequency
      • Sweep-Sine Waveform
  • Power Meter (Option PMC-DSG3000)
    • To Enable the Power Meter
    • Zero Type
    • Zero
    • Frequency Mode
    • Frequency
    • Average Measurement
      • Average Mode
      • Average Number
    • Preset
    • Limit Measurement
      • Measurement Type
      • Maximum Limit
      • Minimum Limit
      • Alert
      • Beeper
    • Recorder
      • Start
      • Stop
      • Count
      • Sample Rate
      • Data Content
    • Relative Measurement
      • Switch
      • Mode
      • Reference Value
    • Statistics
    • Unit
    • System Information
  • RX1000 (Option)
  • Store and Recall
    • File Type
    • Save
    • Recall
    • Rename
    • Delete
    • Copy
    • To Create a Directory
    • Filename Prefix
    • Disk Management
    • System Update
  • To Set the System Parameters
    • Language
    • Reset
    • I/O Configuration
    • Display Setting
    • Power Status
    • Information
    • License
    • Self-test
    • Sanitation
• Chapter 3 Remote Control
  • Remote Control Overview
  • Control Via USB
  • Control Via LAN
  • Control Via GPIB
• Chapter 4 Application Examples
  • To Output RF Signal
  • To Output RF Sweep Signal
  • To Output RF Modulated Signal
  • Pulse Train Application
• Chapter 5 Troubleshooting
• Chapter 6 Specifications
  • Specifications
    • Frequency
    • Level
    • Internal Modulation Generator (LF)
    • Modulation [1]
    • Inputs and Outputs
  • General Specifications
• Chapter 7 Appendix
  • Appendix A: DSG3000 Accessories and options
  • Appendix B: Warranty
• Index