Document Outline

• DIGITAL VNswitch 900GV
• Installation and Configuration
• Contents
  • Preface
  • Overview vii
    • Safety
  • Overview xv
  • 1 Product Introduction
    • Overview 1-1
  • 2 Installing the DIGITAL VNswitch 900GV
    • Overview 2-1
  • 3 Installing the Setup Port Cable
    • Overview 3-1
  • 4 Configuring the Module in a DIGITAL MultiSwitch 900
    • Overview 4-1
  • 5 Removing the Cables, Connector and Module
    • Overview 5-1
  • A Problem Solving
    • Overview A-1
  • B Connectors and Adapters
    • Overview B-1
  • C Product Specifications
    • Overview C-1
• Preface
  • Overview
    • Purpose of the Manual
    • Intended Audience
  • Organization
  • Associated Documents
  • Conventions
  • Accessing Online Information
    • Documentation Comments
    • Online Services
  • Safety
    • Overview
    • Chapter 1
      • Product Introduction
        • Overview
          • In This Chapter
  • What is the DIGITAL VNswitch 900GV?
  • Features
    • Hot Swap
    • Configuration and Management
    • Bridging
    • Ethernet
    • SNMP
    • MIBS
    • RMON
    • VLAN Secure Domains
      • Chapter 2
        • Installing the DIGITAL VNswitch 900GV
          • Overview
            • Introduction
            • In This Chapter
    • Module Components
      • Front Panel Components
        • Figure 2-1: Front Panel LEDs and Connectors
        • Table 2-1: Front Panel LEDs and Connectors
      • Back Panel Components
        • Figure 2-2: Back Panel Components
        • Table 2-2: Back Panel Components
    • How to Install the Module
      • Task 1: Compare the Power Ratings
        • Figure 2-3: Sample Power Ratings
      • Task 2: Seat the Module
        • 1
        • 2
        • 3
        • 4
        • Figure 2-4: Seating the Module
      • Task 3: Verify Initial LED Operation
        • 1
        • 2
        • 3
        • 4
      • Task 4: Connect the LDM Port Cable
        • 1
        • 2
        • Figure 2-5: LDM Port Cable Connection
      • Task 5: Connect the GBIC Connector
        • 1
        • 2
        • 3
        • Figure 2-6: GBIC Connection
      • Task 6: Connect the Duplex SC Cables
        • Warning
        • Table 2-3: Short Wave Length - Black (HP 5601 - 850)
        • Table 2-4: Long Wave Length - Blue (HP 5611 - 1300)
      • Chapter 3
        • Installing the Setup Port Cable
          • Overview
            • Introduction
            • In This Chapter
    • Setup Port Signaling Standards
    • Setup Port Device Cabling
    • Connecting to the Setup Port
      • 1
      • 2
      • 1
      • 2
      • 3
      • 4
      • Figure 3-1: Setup Port Cabling Components
      • Chapter 4
        • Configuring the Module in a DIGITAL MultiSwitch 900
          • Overview
            • Introduction
            • In This Chapter
    • Assigning an IP Address
      • NOTE
        • 1
        • 2
        • 3
        • 4
        • 5
        • 6
        • 7
    • DIGITAL MultiSwitch 900 INSTALLATION MENU
    • [9] Start Redirect Mode
      • NOTE
    • Using Menus to Configure the Module
    • [1] Restart with Factory Defaults
      • CAUTION
    • [2] Restart with Current Settings
      • NOTE
    • [3] Show Current Settings
    • [4] Configure IP
      • NOTE
      • [1] Set SNMP Read/Write Community
      • [2] Add SNMP Trap Addresses
      • [3] Delete SNMP Trap Addresses
      • [4] Set In-Band Interface IP Address
        • NOTE
      • [5] Set Out-of-Band Interface IP Address
      • [6] Set Default Gateway
    • [5] Go to Local Console
    • [6] Product-Specific Options (VNswitch 900GV)
    • [10] Product-Specific Options (MultiSwitch 900)
      • Chapter 5
        • Removing the Cables, Connector and Module
          • Overview
            • Introduction
            • In This Chapter
    • Removing the Cables
      • 1
      • 2
      • Figure 5-1: Removing the LDM Port Cable
    • Removing the GBIC Card
      • 1
      • 2
      • Figure 5-2: GBIC Removal
    • Unseating the Module
      • 1
      • 2
      • 3
      • Figure 5-3: Unseating the Module
      • Appendix A
        • Problem Solving
          • Overview
            • Introduction
            • In This Appendix
    • Normal Power-Up
      • 1
      • 2
      • 3
      • 4
    • LED Descriptions
      • Table A-1: Module LED States
    • Problem Solving Using LEDs
      • NOTE
      • Table A-2: Problem Solving Using the LEDs
      • Appendix B
        • Connector Pin Assignments and Adapters
          • Overview
            • In This Appendix
    • Connectors and Pin Assignments
      • 10BaseT Port (8-pin MJ) Straight-through Connector
        • Figure B-1: 8-pin MJ Straight-through Connector
        • Table B-1: 8-pin MJ Straight-through Connector Pin Assignments
    • Adapters
      • H8571-J Adapter
        • Figure B-2: H8571-J Adapter
      • H8575-A Adapter
        • Figure B-3: H8575-A Adapter
      • Appendix C
        • Product Specifications
          • Overview
            • In This Appendix
    • Product Specifications
      • Table C-1: Product Specifications
    • Acoustical Specifications
      • Table C-2: Acoustical Specifications
      • Table C-3: German Acoustical Specifications
    • Connectors
      • Table C-4: Connectors