Document Outline

• TransSphere TS Wireless Extended Range IP Networking Transceivers Users manual, GFK-2489
  • Contents
  • Introduction
    • TranSphere
      • Model Offerings
    • Applications
      • Long-Range Wireless LAN
      • Combining Serial and Ethernet Devices
      • DNP3 Protocol-Aware Networks
      • Upgrading an Older Wireless Network with Serial Interfaces
    • Cyber Security Suite
      • Intrusion Detection via SNMP Traps
    • Product Numbers
      • Options
      • Accessories
    • Standards
      • ISO 9001 Registration
      • Operational & Safety Notices
      • CSA/US Notice
      • FCC Part 15 Notice
      • Environmental Information
    • Quick Start Instructions
  • Tabletop Setup and Evaluation
    • Connectors
    • Test Setup
      • Step 1—Connect the Antenna Ports
      • Step 2—Measure and Connect Dc Power
      • Step 3—Configure the Access Point
      • Step 4—Configure the Remote Radio
      • Step 5—Connect Terminal Equipment
      • Step 6—Check for Normal Operation
      • Verify Connectivity (PING command)
  • AP Management
    • PC-Based Configuration Software
      • Menu Structure
    • Accessing the Menu System
      • Methods of Control
      • PC Connection and Log-In Procedures
      • Navigating the Menus
    • Basic Device Information
      • Starting Information Screen
      • Main Menu
    • Configuring Network Parameters
      • Network Configuration Menu
      • IP Configuration Menu
      • Wireless MAC Configuration Menu
      • Mobility Configuration Menu
      • SNMP Agent Configuration Menu
      • Bridge Configuration Menu
    • Configuring Radio Parameters
      • Radio Configuration Menu
    • Configuring the Serial Interfaces
      • Overview
      • Local Serial Configuration Menu
      • Remote Serial Gateway Configuration (IP-to-Remote Serial)
    • Security Configuration
      • Security Configuration Menu
    • Wireless Network Menu
      • Remote Management Submenu
    • Statistics And Event Log
      • COM1 and COM2 Data Statistics Menus
      • Remote Serial Gateway Statistics
      • Ethernet and Wireless Packet Statistics
      • Event Log Menu
    • Device Information Menu
    • Maintenance And Tools
      • Reprogramming Menu
      • Configuration Scripts Menu
      • RSG Configuration Script Menu
      • Authorization Codes Menu
      • Transmitter Test Menu
    • Redundancy Menu
    • DNP3 Routing Menu
  • Remote Radio Management
    • Programming Methods
      • Terminal Interface Mode
      • Remote Management via the AP
    • Log-in Procedure
      • Entering Remote Commands
    • Type the command, press SPACE , press ?, then press ENTER .
    • Minimum Configuration for Remotes
    • Commands
      • Detailed Command Descriptions
    • Upgrading Remote Firmware
  • Sample Configurations
    • IP-to-Local Serial Application Example
      • IP-to-Remote Serial Application Example
      • Point-to-Point, Serial-to-Serial Application Example
      • Point-to-Multipoint, Serial-to-Serial Application Example
      • Mixed-Mode Application Example
  • Installation
    • Installation in Hazardous Locations
    • General Requirements
    • Site Selection
      • Conducting a Site Survey
      • Terrain and Signal Strength
    • Mounting Dimensions for Radios
    • Antenna and Feedline Selection
      • Antennas
      • Feedlines
    • Maintaining Compliance at 900 MHz (U.S.A. and Canada Only)
      • How Much Output Power Can Be Used?(U.S.A. and Canada, 900 MHz systems)
      • Calculating System Gain
      • How Much Output Power Can Be Used? (U.S.A. and Canada, 2400 MHz systems)
      • How Much Output Power Can Be Used? (ETSI 2400 Mhz Systems)
      • Calculating System Gain
    • Optimizing Performance
      • Principles of Wireless Network Operation
      • Aiming Directive Antennas for Maximum RSSI
      • Tips for Improving Data Throughput
  • Troubleshooting and Radio Tests
    • Troubleshooting
      • Interpreting the Front Panel LEDs
      • Troubleshooting Using the Embedded Management System
      • Using Logged Operation Events
  • Technical Reference
    • Upgrading Firmware
    • Using Configuration Scripts
      • Sample of an Exported Configuration File
    • Data Interface Connectors
      • LAN/ETH Port
      • COM1 Port
      • COM2 Port
    • Technical Specifications
    • Dbm-Watts-Volts Conversion Chart
  • Terms and Abbreviations
  • Index