MITSUBISHI ELECTRIC HS-HD2000U - Manual (Page 45)

43
7 If you wish to change the record speed, turn the SHUTTLE ring to the right
repeatedly until the record speed is flashing. Change the recording speed by
turning the ADJUST dial. Turn the SHUTTLE ring to the right.
8 To program additional recording times, select an empty program line by turning
the ADJUST dial. Turn the SHUTTLE ring to the right. You will return to the
VCR Plus+ system menu. Continue the VCR Plus+ system programming
procedure from step 3.
9 When you are finished with all programming, check the following:
• If you have a cable box, a digital cable box, a PRIMESTAR
® or a DISH
Network ™ satellite receiver, leave the cable box or receiver turned ON.
• If your VCR does not control your cable box, leave the box tuned to the
station you wish to record.
• Turn the VCR power OFF and make sure the programmed recording light is
lit.
If you want to stop the programmed recording after it starts, press POWER on the
front panel.
VCR Plus+ System Programming Using the Remote Control LCD
1 Load a tape with its erasure prevention tab intact into the VCR.
2 Press VCR Plus+ on the remote control. PlusCode No. appears on the remote
control LCD.
3 Use the number buttons on the remote control to enter the PlusCode number
for the television show you want to record. For example, if the PlusCode
number for the program you want to record is 5678, simply enter 5-6-7-8. See
your local newspaper or TV Guide for PlusCode numbers.
If you enter a number incorrectly, press CANCEL or turn the SHUTTLE ring on
the remote control to the left.
4 Use DAILY/WEEKLY if you want to record your program daily or weekly. If you
want to record a program one time, skip this step.
• select DAILY if you want to record the same channel at the same time,
Monday through Friday.
• select WEEKLY if you want to record the same channel at the same time, on
the same day each week.
5 Press SP/EP under the flip cover of the remote control to select the recording
mode; for example, SP. SP = standard play; EP = extended play.
• select SP if you want to record in SP mode.
• select EP if you want to record in EP mode.
• do not make a selection if you want to keep the recording in the mode that
was previously used.
6 Press TRANSFER. The PlusCode number will be transferred to the VCR, and
the Recap screen will appear. The program you have chosen to record will be
highlighted.
Make sure that the programming contents shown on the screen is correct. The
channel number will appear in blue color. If the displayed number is not
correct, press INPUT to make the number flash, then turn the ADJUST dial to
correct the channel number. Press ENTER to complete.
“S” will appear next to the channel number when you select a satellite channel.
IMPORTANT
If you cannot select the other program line by turning ADJUST dial on the
remote, press PAUSE first, and then turn the ADJUST dial.
POWER
VCR-A
PlusCode No.
TRANSFER DAILY
SP
VCR-A
PlusCode No.
TRANSFER
VCR-A
PlusCode No.
VCR-A
PlusCode No.
TRANSFER DAILY
Timer Recording
¬Program to record
ƒChannel 2
ƒDay Monday 12
ƒStart time 11:30am
ƒStop time 1:30pm
ƒRecord speed SP
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.
¬Program to record
CH DAY ON OFF
10 TH15 9:00p10:30pSP
§ 2 MO12 11:30a 1:30pSP
--- -- --:-- --:-- SP
--- -- --:-- --:-- SP
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.