Integra DSR-7.3 - Manual (Page 69)

69
—
—
—
—
Video1 Language General V2
Exit Move
TV Screen
Component Video
S-Video Out
Screen Saver
16:9(Wide)
S1
S2
On
SETUP
Settings: S1
S2 (Factory Setting)
■ Turning the Screen Saver On and Off
Expert
As a protective function against residual images on the TV
screen or monitor, a phenomenon referred to as “screen burn”,
the screen saver appears when the same screen has been
displayed for a length of time. By default, the screen saver is
turned on. However, the screen saver function can be turned
on and off at your discretion.
Make changes to the [Screen Saver] setting in the Setup
screen Video 1 menu in the [Expert] menu mode (page 67).
Settings: On (Factory setting)
Off
■ Switching the S-Video Output
Expert
You can switch the kind of S-Video signal output from the S-
Video outputs. If you connected your TV with an S-Video cord,
in rare cases the TV picture may appear stretched. In this
case switch the output from [S2] to [S1].
Make changes in the [S-Video Out] in the Setup screen Video
1 menu in the [Expert] menu mode (page 67).
Setting the Video 1 Options
■ Connecting to a progressive scan-
compatible TV
Compared to a standard interlaced TV picture, a progressive
scan TV is capable of stable, flicker-free images.
Set only if you connected the COMPONENT VIDEO OUT
jacks to a progressive scan-compatible TV or monitor.
Make changes to the [Component Video] setting in the Setup
screen Video 1 menu.
Settings: Interlace (Factory Setting)
Use this setting with regular TVs that are not
compatible with progressive scan. Check the TV’s
instruction manual if you are not sure about this.
Progressive
Use this setting with TVs and monitors that have
progressive scan component video inputs. The
Progressive indicator lights up. Check the TV’s
instruction manual if you are not sure about this.
Example (Other than European model)
Example (Other than European model)
Auto Progressive
Switches to progressive scan when 16:9 DVDs are
played,4:3 DVDs uses interlace setting. Your TV/
monitor must be compatible with progressive scan
to use this setting.
Tip
• If this DVD Receiver is set to output progressive-scan video, it’s
possible that the picture will appear stretched when playing discs
recorded in 4:3 format. This happens when the TV’s aspect ratio
is set at 16:9. To see the picture in its correct aspect ratio, change
the TV setting to 4:3.
If your TV can not be switched between 4:3 and 16:9, set this
DVD Receiver to [Interlace] or [Auto progressive]. In Auto
progressive mode, 4:3 discs will be played in Interlace mode,
while discs that are recorded in both 4:3 and 16:9 will play in
interlace mode during the 4:3 sections, and in progressive mode
during the 16:9 parts. Switch your TV’s aspect ratio to the most
suitable setting (for more details, see the manual that came with
your TV). When set to [Auto Progressive], you may see picture
disturbance when this DVD receiver (and the TV) switches
between progressive and interlace modes. This is not a
malfunction of either this DVD receiver or the TV. Picture
disturbance should only occur when switching from a menu
screen to the main feature, for example.
• Progressive scan compatible TVs have on board progressive
circuits. If you prefer, choose “Interlace” in this unit’s setup screen
to view progressive scan video adjusted by the TV’s on board
circuits.
Notes
• If you connect a TV that is not compatible with a progressive scan
signal and choose one of the progressive scan settings, you will
not be able to see any picture at all. With your TV connected
using either the composite or S-Video terminals, choose the
[Interlace] setting in the [Component Video] menu.
—
—
—
Video1 Language General V2
Exit Move
TV Screen
Component Video
S-Video Out
Screen Saver
16:9(Wide)
Interlace
S2
On
Off
SETUP
—
Video1 Language General V2
Exit Move
TV Screen
Component Video
16:9(Wide)
Interlace
Progressive
Auto Progressive
Select Interlace or Progressive
output Component Video
SETUP
Theater-Dimensional
PROGRESSIVE SCAN
IPM
Progressive indicator
* Expert denotes more detailed settings. If the item is not displayed,
please refer to page 67 to display it.