Integra DSR-7.3 - Manual (Page 78)

78
Controlling a TV connected
to the DVD Receiver
Caution
With some brand’s components, some buttons may not work
correctly. In this case, program the command separately.
1
2
By learning a pre-programming code, you can make the
RC-507M remote controller able to operate a product from
another brand.
4
5
T- D Setup IPM
SW Mode Distance
Up/ Down
SP Setup Test Tone CH Sel
1 2 3
4 5 6
0
7 8 9
-- / ---
+10
Learning a pre-programming code
Find the 3-digit number for the
brand name of the component that
you want to operate in the table on
this page.
Turn on the component that you
want to operate.
While holding down Mode TV, press
the +10 button, and then release
both buttons.
The Send indicator lights when the Mode
TV button is pressed and turns off when
the +10 button is pressed. Wait until the
indicator turns off before releasing both
buttons. The Send indicator lights again.
Within 10 seconds, enter the 3-digit
code number.
The Send indicator flashes twice slowly. If
the Send indicator quickly flashes three
times, then either an incorrect 3-digit code
was entered or an incorrect operation was
performed. If this occurs, return to step 3.
Press the button that you
programmed and check if the
system operates correctly.
• If the component does not operate
properly, return to step 3 and repeat the
steps above.
Send
On Standby
Op en/ Clos e
2
T- D Setup IPM
SW Mode Distance
T-D/ ST
A- B
Surround A.Control
-- / ---
Mode
Enter
Repeat
Muting
Up/ Down
SP Setup Test Tone CH Sel
RC- 507M
Audio
Last M Program Random
Late Night Timer
Angle
Clear
Subtitle FM Mode
Input Selector
ENTER
Light
TV
Display
VOL C H
T V In pu t Setu p
DV D Recvr Tape
Tun
Step/ Slow
To p M enu Men u
Retu rn
Clo ck Sle ep
Dimm er
1 2 3
4 5 6
+10 Search 0
7 8 9
+10
Mode TV
Number
buttons
3
TV
BRAND SETTING No.
AIWA 100, 101
AKAI 102, 103, 104
AUDIOSONIC 105
BELL & HOWELL 106
BLAUPUNKT 107
BRIONVEGA 108, 109
CENTURION 110
COLTINA 111, 112, 113
CORONAD 114
CROWN 115, 116
DAEWOO 117, 118, 119, 120, 121
DUAL 122
EMERSON 123, 124, 125, 126, 127
FENNER 128, 129
FERGUSON 130, 131
FISHER 132
FUNAI 133, 134, 135
FUJITSU GENERAL 136, 137, 138
GE 139, 140, 141
GOLDSTAR 142, 143
GOODMANS 144
GRUNDIG 145, 146
HITACHI 147, 148, 149, 150
HYPER 151
INNO HIT 152
IRRADIO 103
JVC 153, 154, 155, 156, 157
KENDO 158
KTV 159, 160
LUXOR 161
MAGNAVOX 162, 163
MARANTZ 164
MARK 165
MATSUI 166, 167, 168, 169
MITSUBISHI 170, 171, 172, 173
MIVAR 174, 175
NEC 176, 177
NOKIA 178, 179, 180, 181
OCEANIC 181
NORDMENDE 182, 183
OKANO 152
ORION 184, 185, 186
PANASONIC 187, 188, 189, 190
PHILIPS 152, 162, 191
PIONEER 192, 193
PROSCAN 194
QUASAR 195
RADIO SHACK 196
RCA 110, 141, 197, 198, 199, 200
SABA 182, 183, 201
SAMSUNG 202, 203, 204, 205, 206, 207, 208
SANYO 209, 210, 211, 212
SCHNEIDER 103
SEARS 213
SELECO 214, 215
SHARP 216, 217
SONY 218, 219, 220, 221, 222, 223
SYMPHONIC 224, 225
TELEFUNKEN 201, 226, 227
THOMSON 228
TOSHIBA 213, 229
UNIVERSUM 230
ZENITH 231, 232
Pre-programming codes
Note:
If more than one code is given in the table, try the code one by
one until you reach the code for your component (i.e. if the first
code does not work, then try the next).