Sanyo TLS-9024P - Manual (Page 18)

AUTOREPEAT RECORDING
Autorepeat Recording
The same tape can be recorded over many times.
œ Follow the Before starting steps, under “NORMAL
RECORDING”.
1
Set the REPEAT REC switch to the “ON” position.
ø The REPEAT indicator will light.
2
Press the MENU button until the (SET UP 3) menu
is displayed.
ø The “ALARM MODE” setting is flashing.
@@@@@@@<SET@UP@3>
öALARM@MODE@@@@@@@Y1
öALARM@SPEED@@@@@@3H
öALARM@DURATION@@@20S
öTAPE@END@MODE@@@@R1
öTAPE@END@OUT@@@@@-3M
öCLOG@DETECT.@@@@@Y
öRS-232C@@@@@@@@@@19200
3
Turn the JOG dial, until the “TAPE END MODE”
setting is flashing.
4
Turn the SHUTTLE ring to set to “R 1” or “R 2”.
(See “Setting the Mode at the End of the Tape”)
5
Press the SEARCH/AUDIO ON button to save the
setting.
6
Press the REC/PLAY SPEED l (or j ) button to set
the recording speed mode.
7
Press the REC button.
ø Recording will start. When the tape end is
reached, the VCR will rewind it to the
beginning, and recording will resume.
ø When the end of the tape is reached, a buzzer
will be heard (if in the (SETUP 2) menu, in the
BUZZER section TAPE END is set to “Y”) and
“OFF” will be displayed until the rewinding
operation starts.
NOTES:
œ If during autorepeat recording there is an alarm
trigger, “AL” is displayed on the digital display and
alarm recording will take place. (Please refer to
page 18, “ALARM RECORDING”.)
œ If the “TAPE END MODE” setting is R 1, the
REPEAT indicator will go off if there is an alarm
trigger. The recording will continue to the end of the
tape then it will be rewound to the beginning and
stop. “OFF” will be displayed on the digital display.
To turn off the buzzer (if in the (SETUP 2) menu, in
the BUZZER section TAPE END is set to “Y”) and
the “OFF” display, press the STOP, EJECT or PLAY
button, or turn the SHUTTLE ring.
œ If “AL” is displayed on the digital display and the
“TAPE END MODE” setting is R1, autorepeat
recording is not possible.
Setting the Mode at the End of the Tape
In the (SET UP 3) menu, you can set the mode of the
VCR mode when the tape reaches the end during
recording.
1
Press the MENU button until the (SET UP 3) menu
is displayed.
@@@@@@@<SET@UP@3>
öALARM@MODE@@@@@@@Y1
öALARM@SPEED@@@@@@3H
öALARM@DURATION@@@20S
öTAPE@END@MODE@@@@REW
öTAPE@END@OUT@@@@@-3M
öCLOG@DETECT.@@@@@Y
öRS-232C@@@@@@@@@@19200
2
Turn the JOG dial, until the “TAPE END MODE”
setting is flashing.
3
Turn the SHUTTLE ring, to set the desired mode.
œ Setting when the REPEAT REC switch is set to
the “OFF” position.
REW. . . . . . . Rewinds the tape to the
beginning, then goes to stop
mode
STOP . . . . . . Goes to stop mode
EJECT . . . . . The cassette is ejected
œ Setting when the REPEAT REC switch is set to
the “ON” position.
R1. . . . . . . . . Autorepeat recording mode is
automatically canceled if there
was an alarm trigger
R2. . . . . . . . . Autorepeat recording mode is
active even if there was an alarm
trigger
4
Press the SEARCH/AUDIO ON button to save the
setting.
RR4Q/EX2 (TLS-9024P GB) Fri. Sept., 29/2000
English
17