Lexicon Digital Controller MC-12 - Manual (Page 189)

MC-12 Appendix
A-11
AUTO LEVELS
FRONT LEFT
CENTER
FRONT RIGHT
SIDE RIGHT
REAR RIGHT
REAR LEFT
SIDE LEFT
SUB (MONO)
SUB RIGHT
LFE ERROR
+0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
N/A
N/A
AUTO DISTANCES
FOR AUTO CALIBRATION
SPEAKER SETUP
SET CROSSOVERS
CHECK MICROPHONES
AUTOMATIC
MANUAL
MAIN MENU
MODE ADJUST
AUDIO CONTROLS
SETUP
SETUP
INPUTS
SPEAKERS
REAR PANEL CONFIG
DISPLAYS
VOLUME CONTROLS
TRIGGERS
LOCK OPTIONS
SET CROSSOVERS
BEFORE CALIBRATING
MIC CHECK REQUIRED
or CUSTOM SETUP AUTO SPEAKER SETUP
DISTANCES
LEVELS
AUTO VALUES APPLIED
PRESS TO VIEW
DETAILS
AUTO SPEAKER SETUP
DISTANCES & LEVELS
DISTANCES
OUTPUT LEVELS
PLACE MICROPHONES
IN PRIMARY LISTENING
POSITIONS
CUSTOM SETUP
40 Hz
60 Hz
60 Hz
60 Hz
40 Hz
OFF
N/A
APART
AUTO SPEAKER SETUP
!CAUTION!
HIGH AUDIO LEVELS
YOU WILL HAVE 10 SEC
TO LEAVE THE ROOM OR
SIT QUIETLY
PRESS TO BEGIN
COUNTDOWN
AUTO SPEAKER SETUP
TEST WILL BEGIN IN
10
PRESS TO SKIP
COUNTDOWN
CUSTOM SETUP SETTING DISTANCES
FRONT LEFT
CENTER
FRONT RIGHT
SIDE RIGHT
REAR RIGHT
REAR LEFT
SIDE LEFT
SUB (MONO)
SUB RIGHT
LFE 0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
N/A
N/A
CUSTOM SETUP SETTING LEVELS
FRONT LEFT
CENTER
FRONT RIGHT
SIDE RIGHT
REAR RIGHT
REAR LEFT
SIDE LEFT
SUB (MONO)
SUB RIGHT
LFE +0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
+0.0dB
N/A
N/A
CUSTOM SETUP AUTO SPEAKER SETUP
DISTANCES
LEVELS
AUTO VALUES APPLIED
PRESS TO VIEW
DETAILS
OK
OK ERROR
ERROR
OK
LEVELS
OK
DISTANCES
OK
(SPEAKER)
SPKR OUTPUT TOO HIGH
(SPEAKER)
SPKR OUTPUT TOO LOW
(SPEAKER)
SPEAKER IS NOT ENABLED
(SPEAKER)
FRONT LEFT
CENTER
FRONT RIGHT
SIDE RIGHT
REAR RIGHT
REAR LEFT
SIDE LEFT
SUB (MONO)
SUB RIGHT
LFE ERROR
0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
0.0ft
N/A
N/A
OK
(SPEAKER)
SPEAKER OUT OF PHASE
(SPEAKER)
SIGNAL TOO LOW
(SPEAKER)
MAY NOT BE ACCURATE
(SPEAKER)
UNABLE TO CALCULATE
(SPEAKER)
SPEAKER IS NOT ENABLED
(SPEAKER)
The AUTO DISTANCES and AUTO LEVELS screens
shown at the right indicate the individual calibra-
tion results for each speaker. Press the and
arrow buttons to highlight the desired speaker cali-
bration parameter. Then, press the arrow but-
ton to view more detailed results for the selected
speaker.
Press the arrow button to return to the AUTO
SPEAKER SETUP results screen shown above (right).
Then, press the arrow button to select the other
calibration procedure or press the the arrow
button to return to the SPEAKER SETUP menu.
When the MC-12 is finished calibrating speaker
distances and output levels, the AUTO SPEAKER
SETUP results screen shown at the left will open on
the on-screen display, indicating the results for
each calibration procedure. Press the and
arrow buttons to highlight the desired calibration
procedure. Then, press the arrow button to
select this procedure. Selecting DISTANCES opens
the AUTO DISTANCES screen shown below.
Selecting the LEVELS option opens the AUTO LEV-
ELS screen shown below.
LIVE! CALIBRATION